Entrance to service menu TV
Akira, Aiwa, Akai, Akura, Avest
Akira CT-14PF9, CTF21TF9R Chassis 3Y01
Processor: LA863324A
On the remote control, press the buttons in sequence: MENU, MENU, V.WIEV (or RETURN), MUTE. Navigation through the menu is carried out by the SLEEP button. Exit-MENU
Akira CT-2155 (chassis 11AK19PRO)
Press the blue button, enter the INSTALLATION menu and sequentially press buttons 4, 7, 2, 5 processor-VESTEL19V1
Akira CT-25DS9A/AN, CT-2 5FS9A, CT-25LS9AE/AIU, CT25IUI9A/AE/AN/AT/ATS,
CT-25RIX9A, CT-25NX/9A(SKD)/AE/AN, CT-25XC9A/AIM, CT-29DS9AE/AIU/AW,
CT-29FS9/A/ATS/C/MK1AT/MTS/MK1AIU, CT-29LS9A/AE/AN/AT/ATS/MTS,
CT-29IUI9A/AE/AN/AT, CT-29NX9AE/AIU, CT-29PF9A/AE, CT-29PS9AE,
CT-29SK9AE, CT-29TJ9AE/AN/ATS, CT-29TK9AE/AIU, CT-29TW9AN,
ST-29XC9A/AE/ATS/MK1 AE/MK 1AM/MK1 AT/MK 1ATS/MK11U, CT-34DS9A, ST-34LS9A/AN,
CT-34PF9A/AE(SKD)/AN/PF9C, CT-34SG9AN, CT-34TP9/A/ATS on 51U11 chassis
To generate service commands, it is necessary to make the following improvements to the standard remote control: to generate the “Screen” command, the output is closed. 7 and 16 remote control chips with a button; additional for the development of the command "Factory" close the pin. 8 and 16 remote control chips using an additional button.
To enter the service menu on the control panel, simultaneously press the VOL +, VOL ~ buttons and, while holding them, turn on the power of the TV. The second option for entering the service mode: after turning on the TV, press the Factory button twice on the modified remote control.
Aiwa 1402, 2002KE, 2102KE.
Pin 8 of the TVPO2066 D05/047 processor is used to enable the service mode. There is a special button S009 on the TV board. By pressing it simultaneously with the DISPLAY button on the remote control, you can enter the service menu processor-TVPO2066 D05/047. If the button is missing, close the pin. 7 common wire and at the same time press the microcontroller on the "DISPLAY" button on the remote control.
Remote-regular. Exit-Button "P" select the line "SERV" and put the TV into standby mode.
Aiwa TV-C142, TV-A215.
To enter the service menu, you must press the hidden button on the remote control, which is located between the buttons 8 and SYSTEM. The latter is located under the false panel of the remote control. Processor-M37220M3-150S. Remote-RC6VT06 Exit-Press the hidden button again.
Aiwa VX-G140, VX-T147
Entering the service mode is possible when the TV time counter is reset to zero. To do this, turn off the TV for 30 minutes by removing the mains plug from the socket, or by discharging the capacitor C101 on the TV disconnected from the network. To enter the service mode, you must set the sound level to a minimum, press and hold the "VOLUME DOWN" button on the front panel, then press the "9" button on the remote control.
Processor-OFC6044D. Remote-regular. Exit-Press button 8 on the remote control.
Aiwa TV-A2110, TV-A2115, TV-A2118
Press the "TEST" button on the remote control.
Processor-TMP87CP38N. Remote control-RC-6VT06.
Exit - turn off the TV with the power switch.
Aiwa TV-C202
Press the "TEST" button on the remote control.
Processor-M37272M8-131SP. Remote control-RC-6VT03 (86-LBR-951-010 or 86-6ME07)
Exit - Press the "FINISH" button on the remote control.
Aiwa TVFA1419, TVFA2019, TVFA2110, TVFA2118, TVFA2588, TVFSA1251, TVFSE141, TVFSE211, TVFSX2150
Hidden buttons on the remote control are used to enter the service menu. The first button (TEST) is to the right of the 0 button, the second button (FINISH) is to the left of the SYSTEM button.
To enter the service mode, press the TEST button, and the AGING MODE starts. Press the CHANEL button to enter the ADJUSTMENT MODE.
The FINISH button resets the hour counter in AGING MODE.
Hours of operation counts the total operating time of the TV.
Exit: Press the hidden TEST button on the remote control
Akai CT-1419, CT-1419A, CT-1419D, CT-1419DM, CT-1419DS, CT-1419DT, CT-1419DTR, CT-1419M, CT-1419P (B20 Chassis)
On the TV panel, simultaneously press the VOL + and VOL- buttons, while holding them down, turn on the TV with the button on the front panel (the TV must be de-energized).
Exit-press on the remote control POWER.
Akai CT-2119PD/PDT, U3E/Y2/Y2E
On the TV panel, simultaneously press the VOL + and VOL- buttons, while holding them down, turn on the TV
Exit-POWER OFF
Akai CT2899, 7171 (chassis B-E2)
For devices with a CCU11 processor, press , C, N. For devices with a CCU12 processor, press the contact in the hole near the keyboard with a screwdriver and immediately press the button S processor-CCU11, CCU12
Exit-LOAD
Akura Crown Minoka СХ25/26/34, CR20NT, CR1406FT, MK1498N/N, MK2183/N
By pressing the special button S009 simultaneously with the DISPLAY button on the remote control, enter the service menu processor-TVPO2066
Exit-TWTEXT
Akura СХ12/23/33, CT-51T/R
While holding the S002 button on the TV board or S201 on its front panel, press button 1 on the remote control
Exit-TV
Avest 54ТЦ-02/09/36/39
Press the VOL- button on the TV panel and the DISPLAY button on the remote control at the same time. Hold the buttons until the letter S appears on the screen. The menu is navigated using the MUTE button processor-TCLM5V-R1P, 87CM38N-1E75
Exit-POWER OFF
Avest 54ТЦ-02/16/88/90
Press the VOL- button on the TV panel and the DISPLAY button on the remote control at the same time. Hold the buttons until the letter D appears on the screen. Navigate through the menu using the MUTE button TCLA02V-01T, 87CM38N-3GP2
Exit-POWER OFF
Avest 54ТЦ-04
To enter the service mode - on the front panel of the TV, press "VOL-", bring to "00", without releasing the "VOL-" button, press the DISPLAY button on the remote control. S will appear on the screen.
Avest 64TC-02PS 88/90, 65TC02-PS, 72TC-02/06/16, 72TC-02PS/86/90
Press simultaneously VOL- on the TV panel and the DISPLAY button on the remote control. Hold the buttons until the letter D appears on the screen. Navigate through the menu using the DISPLAY button, processor-TMP87PS38N, M13VR2V1
Exit-POWER OFF
Avest 37/54ТЦ-01
Menu 1: Press the VOL- button on the TV panel and the OSD button on the remote control at the same time. Hold the buttons until the letter S appears on the TV screen. The menu is navigated with the POWER button. Menu 2: Press the VOL- button on the TV panel and the TV/AV button on the remote control at the same time. Hold the buttons until the letter S appears on the TV screen. Navigate through the menu using the POWER button
processor-LC86F3548A 1JA1
Exit-POWER OFF
Avest TTs-01 (all models)
To enter the menu, press the hidden button on the remote control. The button, depending on the type of remote control, is located either between the VOL- button and the inscription for this button on the remote control, or between the P + and CH + buttons. Operation in the menu is possible after the fifth pressing of the hidden button processor-LC863328A 5W63
Exit-hidden button
Avest 37ТЦ-02
Press the VOL- button on the TV panel and the DISPLAY button on the remote control several times at the same time until the letter D appears on the TV screen. Navigate through the menu using the DISPLAY button
processor-TMP87PS38N, M17VR2
Exit-POWER OFF
Avest 64ТЦF02PS 90, 88, 72ТЦF02 16.06, 72ТЦF02PS 90, 86, 65ТЦ02FPS
Processor TMP87PS38N M13VR2V1
Simultaneously press the VOL- button on the TV panel and the DISPLAY button on the remote control.
The buttons are held until the letter D appears on the TV screen.
Menu navigation - using the DISPLAY button
Bang & Olufsen, Beko, Blaupunkt, Brand
Bang & Olufsen LX4500/5500, L4500/5500, MX3500/5500
Set: Brightness 32, Saturation 32, Contrast 44. Press the TV button on the remote control and close the PCB5 button located next to the VCR sockets for one minute
Exit-STOP or POWER OFF
Veko CTV (chassis 14.1)
Close the remote control chip pins 10 and 17 processor-SAA5563
Exit-Close in the remote control pins 10 and 17
Beko
Input - on the front panel, simultaneously press two channel switching buttons and turn on the TV with a network toggle switch (you can select the menu language)
Blaupunkt IS53/63/72 DIGITAL PRO (chassis FM640-40MC)
launch internal memory processor: close output 1 of the processor (contact MP2) to a common wire and turn on the TV to the network. Enter the service menu: press the i, E buttons on the remote control
processor-MC68HC11F1
exit-i
Blaupunkt MM63-13VT, MM63-14HT (chassis FM240-00)
While holding the i button on the remote control, turn on the power switch
processor - ZC88649P, ZC88644P, ZC424701
Exit-POWER OFF
Blaupunkt MS70-100 DIGITAL PRO (chassis FM600-70), CS82-100 DIGITAL PRO (chassis FM600-71)
Press the i button on the remote control. Select the PROGRAMMER OPTIONEN item, press the ME, AUX buttons. Select the SERVICE MODE position, press the buttons ME, 3, 2, 0, 0 in sequence
Exit-TV
Blaupunkt MS70-76VT (chassis FM100-30CTS)
Brand Chassis ICC9
Use the remote control to switch the TV to standby mode. Turn off the TV with the power switch. Press and hold the blue VT button to turn on the power switch. Press the VT button again
CPU-ST9093, ST92T93J9B1
Brandt Chassis TX807
Press the purple button on the remote control and turn on the power switch
output-POWER OFF
Brandt, FERGUSON, NORDMENDE, SABA, TELEFUNKEN, THOMSON. CHASSIS ICC9, TX-90, TX-91)
1. Stand by - with remote control
2. Turn off the network button.
3. While holding the teletext button (blue) on the remote control, turn on the network.
4. After turning on the TV, release teletext.
5. If it does not work, then release the teletext button in step 4 and press briefly again quickly.
Attention! Entering the service mode is possible in the absence of any signals on the scart.
Exit - stand-by button.
Cirtis, Continrntal
Cirtis C-14/21/25/28M1/M2
Close pins 13 and 23 of the SAA3010 chip in the remote control
processor-MS68NS705T10V
exit-P
Continental CT1412
To enter the service menu, hold down the P +, P- buttons on the front of the TV, turn on the power
processor-ST6375
Daewoo, Daytek, Dual Hanseatic Schneider
Daewoo Chassis СР-375
All changes in the service menu are made only with the help of a special service console
processor-DW5255M2, DW5255RM
Daewoo KR20V1T
Switch TV to channel 91. Set clarity to minimum. On the remote control, press the red button, the green button and the "Menu" button
output-POWER OFF
Daewoo 2594ST, 2896ST, 2898ST (CP-775 chassis)
Entrance through a special service panel R-30SVC
Processor - DW5255S1 (SDA5255)
output-POWER OFF
Daewoo DTC-14V1 /V3/V4/V5/U1ТМ, DTC-20V1/V3/V4/V5/U1TM, DTC-21V1/V3/V4/U1/U3ТМ, KR21U1Т (CP-002 chassis)
To enter the service mode using the user console, you must: select channel 91; set sharpness to minimum; exit the "Menu" mode; quickly press the sequence of buttons: red - green - "Menu", after which the screen should display the inscription: Service Mode OSD. To adjust the set parameters, you must perform the following actions: select channel 91; set sharpness to minimum; quickly press the sequence of buttons: red - green - blue - "Menu", while the inscription D.P. should appear on the screen. OSD. The choice of parameters is carried out by the Channel (Up, Down) buttons. Adjustment of parameters is carried out by buttons Volume (Up, Down)
output-POWER OFF
Daewoo 21U1,21E1,21E5, DTAF14C4TFF, DTAF20C4TF,DTAF14V1TF, DTAF21C6TF Chassis CP-185
Processor TDA9361 Switch the TV to channel 91, set the sharpness to a minimum. Quickly press the buttons on the remote control: red - green - "Menu"
output-POWER OFF
Daewoo: DTC-25G1VM, DTC-29G1VM, DTC-25G3VMR, DTC-25G4VMS, DTC 25G7VM, DTC-29G1TM, DTC-25G1TM (CM-900 Chassis).
Microcontroller (MK) I701 type ТMP87CH38N-3573
To enter the service mode, press the MUTE button on the remote control. After the corresponding picture appears on the screen, simultaneously press the MUTE buttons on the remote control and MENU on the front panel of the TV and hold them until a list of adjustable parameters and their values \u200b\u200bappears on the screen.
Use the PR +/- buttons on the remote control or on the front panel of the TV to select the desired parameter, and use the VOL +/- - buttons to change its value.
The SLEEP button on the remote control or switching to the LF input mode on the front panel are used to control (turn on / off the horizontal white line on the screen) the frame scan.
And with the help of the AV MIX button, the internal test signal generator is turned on: the first press - the PAL signal, the second press - the NTSC signal, the third press - the generator is turned off.
To exit the service menu, turn off the TV with the power switch.
Daewoo DVTF14F6LA, DVTF14F6PA, DVTF14F6FA, DVTF14F6DA, DVTF14F6HA, DVTF20F6LA, DVTF20F6PA, DVTF20F6FA, DVTF20F6DA, DVTF20F6HA, DVTF14F8LA, DVTF14F8PA, DVTF14F8FA, DVTF14F8DA, DVTF14F8HA, DVTF20F8LA, DVTF20F8PA, DVTF20F8FA, DVTF20F8DA, DVTF20F8HA. Chassis CPF420
Processor M37776MB
Switch the TV to standby mode and press the following buttons on the remote control in sequence: BLUE, YELLOW, GREEN, RED, POWER ON
Exit: Press the Power OFF button on the remote control
Daytek DCT-2062-S
Press the DISPLAY, MUTE, SLEEP, FUZZY buttons on the remote control.
Next, press DISPLAY or SLEEP, and the device will enter the service menu
Dual Hanseatic Schneider M4055, ST6714, CTV2703 (DTV-1 Chassis)
press the S button on the front of the TV and the C button on the remote control at the same time
processor-CCU09/10/13, TVM4055
output-TV
Dual Hanseatic Schneider TV5504, TV5520, TV5525 (TV-4 chassis)
Press the blue and red buttons on the remote control at the same time. Immediately after that, press simultaneously P + and VOL + on the front panel of the device
processor-STV6385
output-TV
D ual Hanseatic Schneider TV1170, STV6156 (DTV-2 Chassis)
Simultaneously press the C button on the remote control and the service button, which is located in the bottom row of the remote control
processor-CCU2070
output-TV
Ferguson, Funai, Finlux
Ferguson 51K4/5/7 51L3/7 (ICC5 chassis)
While holding down the VOL- and PROG- buttons on the TV panel, turn on the power switch
processor-HD404919
output-POWER OFF
Funai 2100AMK10 HYPER (HYPER chassis)
On the TV board, short the TP test point labeled FACTORY MODE. Keep these points in contact until a red F appears on the screen.
The program selection buttons on the remote control provide the following adjustments:
1 - calls a horizontal line, centering adjustment
2-ARC
3 - VCO (Voltage Controlled Generator)
4 - centering horizontally
5 - adjustment of color shades
6 - adjustment of static convergence of beams
7 - Checking the purity of color (raster)
8 - RGB cutoff level
9 - RGB span
0 - set brightness, contrast, saturation by default
processor-L7PAL3RD
output-POWER OFF
Funai MK-7, MK-8
Close pins 2 and 14 of the D6600A chip in the remote control. Button 6 in PICTURE SELECT mode switches between character and graphic display of OSD information
processor-R-514, R-584, L7PAL3RD
Funai 2100A MK11
In the remote control, solder any normally open button between pins 2 and 16 of the RT 2461-103 microcircuit. Pressing the button for the 1st time will display the FACTORY mode. When the button is pressed a second time, B/W ADJUST appears on the screen. When pressed 3rd time-ADJUST (geometry). When pressed 4th time - SETUP (setting options). The 5th press exits the service. Using the P-, P+, V-, V+ buttons, the desired parameter values are set
Funai MK11 (chassis 11AK-30)
To turn on the service mode, press the blue button on the remote control. The INSTALLATION menu should appear on the TV screen. Then buttons 4, 7, 2 and 5 are sequentially pressed on the remote control. The SERVICE menu should appear on the screen. For selection required parameters press the "P +" or "P-" buttons, and to change their content - the "+" or "-" buttons on the remote control.
Colored remote control buttons are used in the service menu as follows.
The red button (stereo models only) toggles AVL ON or OFF.
The green button switches the aspect ratio (4:3 or 16:9). This is necessary when adjusting the vertical size in 16:9 mode.
The yellow button turns on the Vertical scan disable mode and is used when setting the accelerating voltage.
The blue button is used for automatic AGC and IF tuning.
Funai TV-2000A MK12
To use a conventional (N0121UD or N0134UD) remote control as a service one, perform the following operations: unscrew three self-tapping screws from the rear panel of the remote control, remove the panel and install jumper J1. To enter the service mode, turn on the TV using the main switch on the front panel of the TV and press the "SLEEP" button on the remote control. On the screen of the microcontroller (for example: 056 version 0.07 is displayed). To save the selected settings, turn the TV off and on using the power switch.
Finlux 4028D
Immediately after turning on the TV on the remote control, press the PRG and EXT buttons
processor-SDA20160
Exit-POWER OFF
Finlux SERIA 5000
Immediately after turning on the TV on the remote control, press the TV, PRG, EXT buttons
processor-SDA20320
output-POWER OFF
Finlux 3021
Press the N1 button on the front of the TV and quickly press the button to the left of the N3 button
processor-SDA2080
Press the button located on the left of the N3 button
Goldstar, Grundig
Goldstar CF-25/29 C26,C36,C76 (MC-51V chassis)
Login - 1. Simultaneously press MENY, --VOL, --PR on the panel., OK- save the changes.
To switch to white balance adjustment: =i - for GG, =? -for RG, =x - for BG.
Exit - off on the remote control.
Goldstar CF-2529C44
Long press the OK button on the Control board and the yellow button on the remote control.
Grundig P 37-065
1. Turn off the network button.
2. Hold down the "i" button on the remote control (TP 711) - turn on the network.
3. Keep the "i" button until the service is received.
4. Exit - turn off the network.
Grundig CUC1825 , CUC1826
Login -- Press the i key and the OK button.
Grundig P39-3010
Processor OECF009B.
Input - Press on the front panel the Vol- TV key and at the same time press on the remote control 6 (9)
The child lock is enabled on the Grundig P37 (4201) TV. How can I unlock it?
On the remote control, press the "VOL +" - "VOL-" - "CH-" - "CH +" buttons in sequence.
Grundig M63F105 ST63F160, ST63F781, E63F911. Chassis CUC1822, CUC1823, CUC1852
Processor: MC68HC11F1
In TV operating mode, press the i button, the message INFO CENTER will be displayed. Select the line SPECIAL FUNCTION and press the OK button. After that, enter code 8500 from the remote control
Grundig Chassis ST82775,ST95775
Processor: SC415008FN4 In the TV operating mode, press the i button, the INFO CENTER message will be displayed. Select the line SPECIAL FUNCTION and press the OK button. After that, the code 8500 is entered from the remote control.
Grundig M55F.., M63F.., ST63F.., ST70F.. Chassis CUC5360, CUC5361, CUC5510 CUC5511
Processor: SDA20561, SDA20562
Press the button (R / C) on the remote control and turn on the TV with the network button
Exit: Turn off the TV with the power button
Grundig ST55F725 ST55F750 ST55F800 ST55F95 Chassis CUC2075, CUC7350
Processor: ZC411867P (MC68HC05T3) MC88671P
Exit: Turn off the TV with the power button
Hitachi, JVC
Hitachi C2578FS, C2589FS, CMT2578 CHASSIS V1
Input - On the front of the TV, press and hold the TV Video button and turn on the TV.
Jvc AV-29PRO
Input -- 1. Set volume value to 04
2. on the remote control - DISPLAY and MENY
Exit - off - power.
Jvc AV-25VM1PF, AV-28VM1PF (JB Chassis). Processor M37201M6-C435SP. Remote control RM C761-1E.
Jvc AV-21SX1EK, AV-25SX1EK (BB Chassis). Processor M37204M8-847SP. Remote control RM C770.
Jvc AV-21TS1EK (BB Chassis). Processor M37221MA-052SP. Remote control RM-760. Jvc AV-21TS1EN (BB Chassis). Processor M37221M6-063SP. Remote control RM-C761.
For all of the above, simultaneously press the "DISPLAY" and "CINENA / GAME" buttons on the remote control.
Exit - press the "DISPLAY" button on the remote control.
Jvc C-JT14EP, C-JT14EI, C-JT21EP C-JT21EL (JG Chassis).
Processor CDA5255-A083. Remote control RM-C370.
Jvc C-J14EP, C-J21EP (JG Chassis).
Processor CDA5223-A019. Remote control RM-C371.
Simultaneously press the "i" (INFORMATION) and MUTE buttons on the remote control.
Exit - press the "i" button on the remote control.
Jvc AV-25S4E/EN/ENS, AV-28S4E/EN/ENS (MX IV chassis).
Processor M37204MC-A45SP. Remote control RM-C663.
Simultaneously press the DISPLAY and VSM > DISPLAY > MENU > MUTE > POWER ON buttons.
SERVICE (FACTORY) is displayed on the screen.
To select menu items, use the CHANNEL± buttons, and to change parameters, use the VOLUME± volume buttons.
Exit the menu - press the FACTORY or POWER OFF buttons again.
Samsung CS2902 (KS2A chassis)
Press the buttons in sequence: STAND-BY, DISPLAU, MENU, MUTE, POWER ON
output-POWER OFF
Samsung CS-29A6HTR PLANO (chassis SK15)
Press the buttons in sequence: STAND BY, DISPLAY, P.STD, MUTE, POWER ON
output-POWER OFF
SAMSUNG CK 5038 ZR TBWCX (chassis SCT11B) CK6202 CK7202 CHASSIS SCT12B
Input -- 1. (stand by) 2. (p.std) 3. (help - ?) 4. (sleep) 5. (power on)
The output is STATUS or HILDDEN.
SAMSUNG CS7272 PTRBWX CHASSIS SCT 51A, CS-721, CS-723
Input -- 1. (picture off) 2. (sleep) 3. (p.std) 4. (mute) 5. (picture on)
Exit - off - power.
S AMSUNG TVP3350, TVP5050, TVP5350 (monoblock) CHASSIS: SCV11A, B Input--- Stand-By P.Std Menu Sleep Power On
Samsung TV, one of the combinations should work:
Option 1: hidden button on the remote control (HIDDEN)
Option 2: Stand-by->P.STD->Help->Sleep->Power-On
Option 3: PICTURE OFF - SLEEP - P.STD - MUTE - PICTURE ON
Samsung LW17M24C, LW20M21C Chassis: VC17EO, VC20EO
To switch TVs into service mode, turn it on and press the following buttons on the user's remote control: POWER OFF - INFO - MENU - MUTE - POWER ON.
Sanyo, Schneinder, Seg, Seleco, Sharp
Sanyo C28WK1N (chassis A8-B)
While holding the MEMORY button on the TV panel, press the NORM button on the remote control
processor-M37201E6-E8WW
output-POWER OFF
Sanyo C28EH65N
processor-SAA5290
exit-RECALL
Sanyo C28ER17EE-00, C28EH/ER14/89 (EB4-A chassis)
Press the F button on the remote control and immediately the P + button on the TV panel
processor-SAA5290ZP/033
exit-RECALL
Sanyo CEP2572-00, CEP2573-00, CEP2872, CEP2873 (chassis ED-1.ED1-28)
Press the SERVICE, MEMORY buttons on the TV panel at the same time
CPU-SAB8032A/ AH/A-R
output-TV/AV
Sanyo SE-28DN5C
The TV has two service menus. The second menu cannot be entered without closing the first. Entering the first menu: while holding F / OK on the remote control, press the P- button on the TV panel. Entering the second menu: while holding the green button on the remote control, press the P- button on the TV panel
Sanyo CEP2876DA (chassis EB1-28)
Press the MEMORY button on the TV and immediately the INDEX/MENY button on the remote control
processor-SAB8032
output-TV
Schneinder-Polcolor STV6550 (DIGIT2000 chassis)
Press the S button on the TV and the C button on the remote control at the same time
processor-CCU2070
output-TV
Schneinder-Polcolor DIGITECH-300 (chassis DTV-3, DTV-4)
Service login:
1. Turn on the network button.
2. While holding down the red and blue buttons on the remote control (remote control 204) for exactly 5 seconds, without releasing them, press the volume + and CH- buttons on the TV simultaneously.
Dial the combination clearly, maintaining a strict time interval.
processor-CCU3001
Exit - turn off the power.
Schneinder-Polcolor TV4, TV8
From any remote control of the RC-5 standard, give the command "TV", it is similar to the command from the native remote control when you press the red and blue buttons
SEG ST7800
Seleco 21/25/28SS564 (BS950 chassis)
Close the output 31 of the C11 processor to a common wire.
Press the R/C button on the remote control
Processor-SECO18A, SECO19 (SE8800UP)
exit-TETEXT
1. Power off.
2. Vol - at the same time CH + on the panel.
3. Power ON on the panel and hold item 2 until it starts.
Sharp 54AT...15SC (chassis 5BS-A)
While holding the VOL- and CH + keys on the TV panel, turn on the device with the power switch
output-POWER OFF
Sharp VT-1428M, VT-2128M
Set the TV to standby mode and press the CH, UP buttons on the remote control for 2 or more seconds.
Simultaneously press the POWER button
exit-MENU
Sharp 14D-SC, 14B-SC, 20B-SC, 14D-CM, 21D-CK1, CV-2132CK1 (PAL-A Chassis)
On the TV board, set the switch S1008 to the service mode position
exit-S1008
Sharp 14R-SC/M8/M10, 14R-W, CV-14RU (SP-70 Chassis)
On the TV board, set the switch S1006 to the service mode position
exit-S1006
Sharp 25FN1.29FN1 (chassis SP-42M)
On the TV board, set the switch S1001 to the service mode position. To display information on the screen, press the S-MODE key on the remote control
Processor-M37210M4-775SP
exit-S1001
Sharp DV-5450SC, DV-5451S, DV3760, DV-3750S (S3B Chassis)
To enter the service mode, close the output 5 of the processor to a common wire. Then press the MODE button on the remote control. -SERV- will appear on the screen. Then remove the jumper. The choice of adjustment parameters is carried out using the CH- and CH + buttons
Processor-IX1492BMN1, IX1492BMZZ
exit-MODE
Sharp DV-5460SC, DV-5461SC, DV5462SC (chassis 4BS-A)
Connect pin 5 of the processor to common through a 100 ohm resistor. Then press the MODE button on the remote control. -SERV- will appear on the screen. Then remove the jumper. The choice of adjustment parameters is carried out using the CH- and CH + buttons
Processor-IX1492BMN3
exit-MODE
Sharp DV-6340S, DV-7032S (chassis 4BS-C)
To enter the service mode, you need to connect points 2 and 6 in the VIDEO block
Processor-SAB8032
output-POWER OFF
Sharp 37/54AM-12SC, 37/54M-16SC, 37/54AM-23SC (chassis 5BS)
Processor-IX1572BMNO (SDA20561-A529)
exit-MODE
Sharp 63CS-03SC, 70CS-03SC, 70AS-05S (SC Chassis)
While holding down the VOL- and CH + keys on the TV panel, turn on the TV with the power switch
Processor-SAB-C502
exit-STANBY
Sharp 54DT-25SC, 54DT-26SC (CA-1 chassis)
While holding down the VOL- and CH + keys on the TV panel, turn on the TV with the power switch
Processor - IX1655BMN1, IX1669BMNO (SDA5222)
exit-MENU
Sharp DV-25071S (D3000 Chassis)
Press switch S1401 located in the RWB-B module
Press switch S1401 again
Sharp 14/21JN1 (chassis SP-51)
To enter the service menu, you must apply 5 V to pin 37 of the processor
Sharp DV-5935H (BCTV-A Chassis)
Install a jumper between points 2 (case) and 6 (SV) located on the signal board of the TV. Turn on the device and remove the jumper
Processor-SAB8032
exit-Put a jumper. Turn off TV. Remove jumper
Sharp DV-5101H, DV-5103H (EURO-DS1 chassis)
Install a jumper between pin 2 (case) and pin 6 (SV) located on the TV signal board
CPU-CCU3000
exit-Press SKIP on the remote control. Turn off TV. Remove jumper
To enter the service menu, press the buttons on the remote control: MENU, INSTALL, 4, 7, 2, 5
Serino, Shivaki, Sony, Supra
Serino STV2820
If you accidentally activate the access code to the TV, you can reset the code by long-term (1.5 minutes) pressing the VOL- button
Shivaki Chassis 11AK19
First, enter the installation menu with the INSTALL key, then press the keys on the remote control in the following sequence: 4, 7, 2, 5. Find the ADJUST position in the menu (all adjustments are changed through it)
Shivaki STV1415, STV2113MK2 (chassis 11AK20)
To enter the service menu, press the following keys on the remote control: VOL-Prog, -, TV. Parameters are selected with the P +, P- buttons, and the parameters are changed with the VOL-, VOL + buttons.
To save the parameters, press the front button exit-TV
Shivaki STV1414/T, STV2110 (chassis DY300, DY321)
The menu is entered using a special service panel (SVC button)
Click on SVC again
processor-STV2905 (chassis DY-900)
Press the SERVICE button on the remote control. In this case, the OSD information: “Line SVC” will appear on the screen. After that, press the button (-/--) on the remote control
Shivaki STV-2119 (H-501 chassis)
To enter the service menu, you must sequentially press the buttons on the remote control: DISPLAY, MUTE, SLEEP, FUZZY. Further, after pressing the DISPLAY button, geometry and AGC adjustments are made, and after pressing the SLEEP button, white balance
Shivaki STV-216 MULTI, STV-2129 CS-29A6HTR (chassis H-50V, MS-41A)
To enter the service menu, you must sequentially press the buttons on the remote control: ST. BY, MUTE, MENU, POWER ON
Shivaki STV-2139 mega
Press and hold the VOL- button on the front of the TV and then press the -/- - TV/Video - Display buttons on the remote control in sequence. Use the CAN+ and CAN- buttons to select parameters, and use the VOL- and VOL+ buttons to adjust them.
To save the new parameter values, press the red button on the remote control. To exit the service mode, turn off the TV with the power switch.
Sony KV-M1440, KV-M2171, KV-M2181.KV-M2101, KV-2170, KV-2180, KV-2540, KV-25X1.KV-29X1 -T25MF1, KV-14V5, KV-S29RN1/34RN1/ 25М1К, KV-16WT1, KV-C2173, KV-C2171.KV-2501, KV-C2503, KV-C2508, KV-C2509, KV-21T10R, KV-21C4 , KV-21X4, KV29F3A, KV-G25T1, KV-X2901, KV-X2900B, KV-X2903E, KV-X2002U, KV-29X5A, KV-29FX11A, KV-C2901, KV-C2903, KV-C2908, KV-C2909 , KV-29X1, KV-V5D, KV-14V6, KV-14V5, KV-M2171, KV-M2181KR, KV-16WT1A/K/R/U (chassis BE4, BE^A, BE-3B, BE-3D, BE-3S, G1.BE-5, FE-1)
Switch the TV to standby mode, press the buttons on the remote control: ?, 5, VOL +, TV
Processor-CXP85340A, SAA5290, SDA5250
output-POWER OFF
Sony KV-S2941A, KV-2551, KV-S29JN1/MN1/SN1, KV-S34JN1/MN1/SN1 .KV-S2921, KV-S2922, KV-S2923,25T1R, KV-S2941,KV-S2942U, KV-S2943E, KV-29E1R, KV-X2560, KV-S2952, KV-S2953 (chassis AE-2, AE- 2A, AE-2B, AP-2, AE-2F AE-3)
Turn on the power of the TV by simultaneously pressing the P +, P- buttons on the front panel of the unit. After that, the message TT_ will be displayed on the screen.
Then press the MENU button
CPU-SDA30C162, SDA30C164
output-POWER OFF
Sony KV-S2941.KV-S2942, KV-S2943 (chassis AE-2F)
Press 2 times the POWER button on the remote control
Processor-SDA30C162GEG
Sony KV-25/29K1.KV-28FD1E/K, KV32FD1.KV-29C3 (chassis AE-4, GE-1)
While holding down the PROG + and PROG- buttons on the front of the TV, turn on the network switch
CPU-SDA30C164
output-POWER OFF
Sony KV-G21M1/G21P1/G21S11, KV-T21M1/T21MF1/T21MN1/T21MN11
Input - press a combination of buttons on the remote control 1 (UP) 4 (DOWN).
Press the MUTE button to display the WRITE (Green) screen. Press the 0 key to enter into memory.M
Exit-- press 2 times on the POWER button.
Processor-CXR85116V
output-POWER, POWER
Sony KV B21M1 with RM 870 remote control (chassis BG1S, BG2S).
The menu parameters are selected using buttons 1 and 4 on the remote control, their adjustment - with buttons 3 and 6, recording in memory - with the MUTING button, and canceling the recording - with button 0.
Sony KV -ES29M61, ES29N90, ES34K90 Chassis AG3 with remotes RM916, RM-959
To enter the service menu, switch the TV to standby mode and press the DISPLAY - 5 - VOL + - POWER buttons in sequence.
Sony KV-K29CF1(RM-845P). Chassis G3F
To enter the service menu, switch the TV to standby mode and press the DISPLAY - 5 - VOL + - POWER buttons in sequence.
The menu options are selected using buttons 1 and 4 on the remote control, press the MUTING button, the message WRITE (WRITE mode call) will appear on the screen, press the 0 button to write to the memory.
Supra STV2091W
Access to the service menu is carried out using universal remote control RZ-66 (AV-8), (code 159).
Button assignment: Mute - menu, F - general reset in normal mode, G - entry into the service, F - exit from the service, data is saved, E - turns on in the service mode heat mode run. The same button exits this mode.
Supra TAU CT34WX50
Press the VOL- button on the TV and quickly press the INFO button on the remote control three times
Telefunken, Tetestar, Thomson, Saba, Toshiba
Telefunken Chassis 618
Press the P, VOL buttons and turn on the power switch. Hold the buttons until SS is displayed on the indicator
Processor-HD404018
output-POWER OFF
T elefunken: MA111E, MA116ET, MA211E, MA216ET, MF211E, MF216ET, MF220E chassis TX807 C/CS
Input - put the TV in standby mode. Switch off with the power button and wait until the standby LED goes off. While holding the button on the remote control, turn on the network button. After the raster appears, press the button on the remote control again
Tetestar 6855, 6870 (RT-92 chassis)
Simultaneously press the SUB-PAGE buttons on the remote control and VOLUME-DOWN on the TV panel
Processor - TDA935x/6x/8x
Thomson, Saba 21MG77C (TX-90, TX-91.TX-92, TX-92F chassis)
To enter the service mode, you must:
put the TV into standby mode using the remote control;
turn off the TV with the network button; while holding the blue teletext button on the remote control, turn on the network;
turn off teletext after turning on the TV
Processor-ST9291
output-POWER OFF
Thomson, Saba 28DTT78ME, 2WS78KE/M/MP, 28DH78K, 28DU78K, 28DU88M/NE, 28DU98MP, 32VT88NP, 37WS88ME (ICC191 chassis)
To enter the service menu, while holding down the PR- and VOL- buttons on the front panel of the TV, turn on the network switch
Thomson, Saba 52RW64E, 44RW65ES, 52RW65ES, 52RW77WS
Turn on the TV while holding down the PROG- and VOL- buttons
Thomson, Saba 63MT68L, 72MT68L, 63DF68L, 25DH65J, 72DF68L, 29DH65J, 29DF65J, 85MX69L (ICC9 Chassis)
Turn on the TV by holding the blue button on the remote control for 5 seconds Processor-ST9093
output-POWER OFF
Thomson, Saba Chassis 1СС10
Method 1: Turn on the TV by holding the blue button on the remote control for 5 seconds
Method 2: Turn on the TV by holding the PROG- and VOL- buttons for 8 seconds
Processor-ST90R91
output-POWER OFF
Thomson, Saba 14CB10C
Monoblock. Simultaneously press the Stop, Pr+ buttons on the local keyboard of the device and turn on the device with the network button. The first digit for the DK mode out of 16 that appear should be 4, for the Russian-language menu, the 15th and 16th digits should be 1 and 5, respectively
Processor-TMRA8700-xxxx
Thomson: 14MG15ET, 14MK15ET, BK 17TH, 20DG15ET, 21DG17E, 21MT10E, 21MG110R/130R, 21MF10E, 21MX17E (TX807 C/CS chassis).
Processor TMP47P1637VN (TDA9351PS/N1/1L0180).
Input - put the TV in standby mode. Switch off with the power button and wait until the standby LED goes out. While holding the button on the remote control, turn on the network button. After the raster appears, press the button on the remote control again.
Toshiba 2050, 2150, 1478XR, 1450, 1458, 20N3, 2163DB/DD/DF/DN/DS (chassis S5E, C6S)
To enter the service mode, do the following:
press the MUTE button on the remote control;
press MUTE again and do not release;
press the MENU button on the TV. The last button is hidden behind a small hole on the front of the TV.
Processor-M3722M6-A80SP/A81SP/B 80SP/B84SP
output-POWER OFF
Toshiba 2185XR
To enter the service menu, you must:
press the MUTE button on the remote control;
press the MUTE button again and do not release it;
press the MENU button on the TV. Each press of the CHANNEL UP button changes the adjustment positions. Each press of the VOLUME+ and VOLUME- buttons changes the data
output-POWER OFF
Toshiba 2929DD
While holding the F button, press the AV button on the remote control. Then immediately press: 1, 0, 4, 8
Processor-CXR80424-144
output-POWER OFF
Toshiba 28W7D (C7SS chassis)
Press the MUTE button on the remote control. Press it again and, while holding, press the MENU button on the TV
Processor-TMP87CS38N-3477
output-POWER OFF
Unimor
Unimor SIESTA-3 (Siesta 3 chassis)
Connect output 21 of the processor to a common wire. Press P + and P- on the TV and turn on the power switch
Processor-SDA20562-A508
output-POWER OFF
Unimor SIESTA-3A (chassis Siesta FOR)
Connect output 21 of the processor to a common wire. Press the P + and R- buttons on the TV and turn on the power switch
Processor-SDA20562-A515/A522
output-POWER OFF
To be continued....
AIWA TV-C142, TV-A215
Login - press the hidden button on the remote control, located between the buttons 8 and SYSTEM (under the false panel).The exit is the same as the entrance.
AIWA 1402, 2002KE, 2102KE.
On the TV board, press the special button S009 simultaneously with the (DISPLAY) button on the remote control. To exit, turn off the TV from the front panel
AKAI CT-2119PDPDT, U2EY2Y2E
Entering the TEST MOD mode on the TV, press the + and - buttons while holding them to turn on the TV.
Exit - press the POWER button.
AKAI CT2899/7171
For the CCU11 processor, press the buttons (°), (C), (H) on the remote control. For CCU12, press the contact in the remote control hole near the keyboard with a screwdriver and then immediately the button (S). To exit, press the button (LOAD)
AKAI CT2161, CT2565, CT2567, CT2865, CT2867
On the remote control, press the buttons (MUTE), (OK), (TV). Record data - button (OK). Exit - (TV)
AKIRA CT-14PF9
Dial (MENU), (MENU), (V.WIEV), (MUTE) on the remote control. Press the (SLEEP) button to turn pages. Exit - button (MENU)
AKIRA CT-2155
Press the blue button, enter the INSTALLATION menu, press the buttons (4), (7), (2), (5). To exit, turn off the TV from the front panel
AKURA, CROWN, MNOKA СХ25/26/34, CR20NT, CR1406FT, MK1498N/N, MK2183/N
Pin 8 of the processor is used to enable the mode. There is a special button S009 on the TV board. Press it simultaneously with the (DISPLAY) button on the remote control. Exit - button (TV/TEXT)
BEKO
Input - on the front panel, simultaneously press the two channel switching buttons and turn on the TV with the network toggle switch (you can select the menu language).
BLAUPUNKT I563(72)53 DIGITAL PRO
To turn on the internal memory of the processor, close its output 1 (contact MP2) to a common wire and turn on the TV. Press buttons (i), (E). Click on them again to exit.
BLAUPUNKT MM63-13VT, MM63-14HT
While holding the button (i) on the remote control, turn on the power switch on the TV. Exit - (POWER OFF)
BLAUPUNKT MS70-100 DIGITAL PRO, CS82-100 DIGITAL PRO
Press the button (i) on the remote control. Select the PROGRAMMIER OPTIONEN item and press the (ME), (AUX) buttons. Select item SERVICE MODE. Press the buttons (ME), (3), (2), (0), (0). Exit - (TV)
CIRTIS C-14/21/25/28M1/M2
Close pins 13 and 23 of the microcircuit (SAA3010) in the remote control. Exit - button (P) on the remote control
CONTINENTAL CT1412
While holding the buttons (P+) and (P-) on the front of the TV, turn on the power switch. To exit, turn off the TV from the front panel
DAEWOO KR20V1T
Switch TV to channel 91 . Reduce clarity to a minimum. On the remote control, press the buttons (red), (green), (menu). Exit - (POWER OFF)
DAEWOO 2594ST, 2896ST, 2898ST
To enter, you need a special service console R-30SVC. Exit - (POWER OFF)
DAEWOO 21U1,21E1,21E5
Select TV channel number 91 . Set the sharpness control (SHARPNESS) to minimum and quickly dial (RED), (GREEN), (MENU) on the remote control. Output -(POWER OFF)
DAYTEK DCT-2062-S
On the remote control dial (DISPLAY), (MUTE), (SLEEP), (FUZZY). The next press of the (DISPLAY) or (SLEEP) button will turn on the service menu. To exit, turn off the TV from the front panel
FERGUSON 51K4/5/751L3/7
While holding down the (VOL-) and (PROG-) buttons on the TV panel, turn on the power switch and hold the buttons until a message appears. Exit - (POWER OFF)
FUNAI 2100A MK10 HYPER.
To set the TV to service mode, it is necessary to short-circuit the TP test point labeled FAKTORY MODE on the board until a red F appears on the screen. Exit - (POWER OFF)
FUNAI MK7, MK8
Close pins 2 and 14 of the D6600A chip in the remote control. Button (6) in PICTURE SELECT mode switches the symbolic-graphic output of OSD information. To exit, turn off the TV from the front panel
FUNAI 2100AMK11
In the remote control, solder the button between pins 2 and 16 of the RT2461-103 chip. When you press the button once, FACTORY appears on the screen; the second time - B / W ADJUST (adjustment of the kinescope modes); third time - ADJUST (geometry); fourth time - SETUP (setting options); fifth press - exit from the service. Buttons (P-), (P+), (V-), (V+) set the required values in the required places
FINLUX 4028D
Immediately after turning on the TV, send commands (PRG), (EXT) from the remote control. Exit - (POWER OFF)
FINLUX SERIA 5000
Immediately after turning on the TV, send commands from the remote control (TV), (PRG), (EXT). Exit - (POWER OFF)
Finlux 3021
Press the button (N1) on the front of the TV and quickly press the button located to the left of the button (N3). To exit, press the button to the left of (N3) again
GOLDSTAR CF-25/29 C26,C36,C76 (MC-51B chassis).
Login - simultaneously press MENY, --VOL, --PR on the panel. OK - save changes. To switch to white balance adjustment: =i - for GG, =? -for RG, =x - for BG.
Exit - off on the remote control.
GOLDSTAR CF-2529C44.
Long press the OK button on the Control board and the yellow button on the remote control.
GRUNDIG M63-105, ST63-160, ST63-781, E63-911
To start the internal memory of the processor, close its output 1 (contact MP2) to a common wire and turn on the TV to the network. Press the button (i) on the remote control (TP760). Use the buttons (P+) and (P-) to select SERVICE. Press (OK) and enter the code using buttons (8), (5), (0), (0). Exit - press the button (i)
GRUNDIG ST82775, ST95775
Press the button (i), INFO CENTER will appear. Select SPECIAL FUNCTION with buttons (P+) and (P-) and press (OK). Enter the code using buttons (8), (5), (0), (0). Exit - button (i)
GRUNDIG M55-..., M63-..., ST63-..., ST70-...
Press the button (Р/С) on the remote control, turn on the power switch. Exit - (POWER OFF)
GRUNDIG ST55-725, ST55-750, ST55-800, ST55-95
While holding the button (i) on the remote control, turn on the power switch. Exit - button (i)
GRUNDIG P37..., P40..., P42..., P45..., P50..., T51..., T55...
While holding the button (i) on the remote control (TP720), turn on the power switch. Remember value - (OK). Exit - (POWER OFF)
GRUNDIG BOSTON ST270/8/IDTV/LOG
Press the key (i) on the TV panel and the button (OK) on the remote control. Remember value - (OK). To exit, press the buttons (i), (POWER OFF)
GRUNDIG GV200VPS
On the remote control, press (CODE), then the buttons (4), (9), (3), (4) Then confirm (OK) and press (STAND BY). To exit, turn off the TV from the front panel
GRUNDIG M70-100, M70-580, M82-100, M95-100, M70-681 IDTV
Press the button (i) on the remote control. Use the (P) button to call up the SERVICE DEMO mode, press (OK), (AUX). Call SERVICE MODE with buttons (OK), (8), (5), (0), (0). Unlock - (VIDEOTEXT), (PAGE), (CANSEL), (PAGE), (OK). To remember the adjustments, you need to connect pin 7 of the SDA3526 chip to a common wire. Exit - button (i)
GRUNDIG М70-290/9, М84-211/8
Press the button (i) on the remote control. Use the (P) button to call up the DIALOG CENTER mode, press (OK). Call For authorizes dealer- (OK), (8), (5), (0), (0). Exit - (POWER OFF)
GRUNDIG P37/40/50, T51 /55/65
Close pins 6 and 10 of the MC144105 processor in the remote control. Exit - button (i)
GRUNDIG Р37-065/070/730
While holding the button (i) on the remote control, turn on the power switch. Exit - (POWER OFF)
GRUNDIG М82-169/9 IDTV, Greenville 7003 text, Greenville 7003 NIC/TOP, ST63-700 text, ST63-700 NIC/text, ST63-700 NIC/TOP, ST63-780 text, ST63-780 NIC/TOP, ST70 -700 text, ST70-700 NIC/text, ST70-700 NIC/TOP, ST70-780 text, ST70-780 NIC/TOP, ST72-860 TOP, ST72-860 NIC/TOP, Greenville 550 SE 5586 TOP, ST 55 -800 TOP, ST 55-850 TOP, ST 55-710 NIC/TOP, ST 55-725 FT/GB, ST 55-800 NIC/TOP, ST 55-850 NIC/TOP, ST 55-850 FR/ TOP, ST 55-900 FR / TOP, M 70-269/9 Reference, TrentoSE7016/9Ref./PIP, M 82-269/9 Ref., Denver SE 8216/9 Ref./PIP, M 82-269 PAL-plus/ LOG, M 72-410 Ref., M 72-410/9 Ref., M 72-410 Ref ./PIP, M 95-410/9 Ref./PIP, MW 70-100/8, Berlin SE 70-100 /8
Dial (INFOCENTER), (SPECIAL FUNCTIONE), (SERVICE) on the remote control and enter the code (8), (5), (0), (0). Exit - (POWER OFF)
HITACHI 43FDX, 53FDX
Open the front panel (four screws), remove the central panel (six screws), press the blue button on the left corner of the dial board. Press this button again to exit.
HITACHI C25/28P445VT, C21/25/28P745VT, C28P405VT
Dial on the remote control (P), (*), (O / V), (#), (M). Exit - (TV)
HITACHI C2575/76/77, C2975/76/77, CL25/29/76, CP25/29/76, C28300TN
While holding down the buttons (VOL +) and (VOL-) on the TV, turn on the power switch. Exit - (POWER OFF)
HITACHI CS2840TA
Dial on the remote control in one second (-/--), (MENU), (TV). Exit - (POWER OFF)
HITACHI C2578FS, C2589FS, SMT2578
On the front panel of the TV, press the button (TV / AV) and, while holding it, turn on the TV. To memorize each parameter, press the (ENTER) button. Exit - (POWER OFF)
HITACHI CL2894/TAN/TA, CP2894/TAN/TP/AN
Turn on the TV and immediately dial the combination (MENU), (TV), (I) on the remote control. Exit - (POWER OFF)
HITACHI C25/2844TN, C25/2864TN
While holding the buttons (VOL +) and (VOL-), turn on the power switch. Under the remote control cover, press the button with the bracket sign twice. Exit - (POWER OFF)
HITACHI CP2133TA/AN, CL2133TA/TN
Turn on the TV and immediately dial the combination (G), (M), (PROG) on the remote control. Exit - (TV)
JVC AV-29PRO.
Entrance:
1. Set the volume value to 04.
2. On the remote - DISPLAY and MENY.
Exit - off - power.
JVC-21TE, G21T, G250MX
Input - simultaneously press the remote control "display", "picture mode" 2 times.
off timer -- remember.
Exit - press MUTE twice.
JVC-C21ZE (21TE, 14TE, 21ME, 14ME, 14W) G21T G21OT G25MX.
Menu entry:
+
SERVICE MENU
1.VSM PRESET
2.SUB VSM
3.IF V/C
Menu control:
Press 1,2 or 3
PICTURE ADJUST - SELECTING ITEMS IN THE MENU
+PICTURE ADJUST - CHANGE ITEM
-PICTURE ADJUST - --- // ---
DYSPLAY- CALL MENU ON SCREEN
OFF TIMER- SAVE CHANGES SYSTEM CONSTANT
MUTE - SAVE CHANGES
MUTE - EXIT
LG MC64 and MC84.
Login - - simultaneously press OK on remote control and on the TV panel.
MAGNAVOX.
Entrance:
1. Press the following combination on the remote control: , , , , , . The channels will change.
2. press MENU
Attention! This only works on *SOME* Magnavox TVs.
The output is the POWER button on the TV.
MITSUBISHI CT-21M5EETRT, CT-25M5EENETETNRTRTN.
Input - press the service switch S701 (next to the tuner), then the button 9 (within 5 seconds).
"*" - switching the adjustment display, "2" - "8" - adjusting the code, "6" - "4" - adjusting the data, "0" - writing to memory, "1" - canceling changes before writing to memory.
Exit -- stand by.
MITSUBISI CT-29B3EEST.
Input - turn on the power. Press the service switch S701 (next to the tuner), then button 9 (within 5 seconds).
Record - button 4.
Buttons 2 and 0 change the adjustment code, buttons 5 and 7 change the data value.
NOKIA 6364, 7364 CHASSIS 2B-F (chassis EVROSTEREO 2B-F).
Input -- 1. (-/--) 2. (MENY) 3. (TV) -- all within 1 second.
The record of the result is MEMO.
Exit - off from the remote control.
NOKIA, SELECO, SABBA ITT, TELEFUNKEN (STEREO PLUS chassis).
Input -- 1.(mute) 2.(OK) 3.(tv), record result “OK”
Exit -- TV
PANASONIC (chassis MX-3, MX-3C).
Hotel mode:
1. On the remote control - off timer, on the panel CH. UP -- enabled.
2. On the remote control - off timer, on the panel - VOL. – off
Input -- simultaneously press RECALL on the remote control and - VOL . on the panel.
Exit - press NORMAL twice on the remote control.
PANASONIC TC-29V50R CHASSIS MX-2A.
Entering the adjustment mode - press the button of the service switch S1101 (next to the centering switch). SNK will appear on the screen. Button S1103 (FUN) --- choice necessary adjustment.
Exit -- press S1101.
PANASONIC TX-21AD2C, TX-29A3C, TX-25A3C CHASSIS EURO-2, EURO-1.
Set the BASS bass control to maximum, TREBLE the treble control to minimum. Press the F button on the TV panel simultaneously with the REVEAL button on the remote control.