Easy and quick self-configuration of a Wi-Fi router. How to find out your connection type

Setting up a router is not an easy procedure, but we are ready to help you understand all its intricacies. Just read the instructions below carefully, and in just a few minutes you can easily set the parameters you need and get started!

#1. Connection

Before you configure the router yourself via a computer, you need to connect it:

  • Insert the Internet cable into the WAN/Internet port;
  • Install the end of the network cable into the LAN port of the device;
  • Place the other end into the connector on the PC;
  • Connect the model to a power outlet and press power on.
  • Ready!

We hope that this brief instructions helped you figure out the first steps, and you can read more about the connection process on the website. Now you can safely move on to the instructions, which tell you how to configure it yourself correctly. WiFi router.

#2. Login to the web interface

We would like to warn you that WiFi setup The router can be accessed online through a browser only after the device is turned on. When you activate the work, distribution of the wireless network with factory settings (login, password) will begin. You can change the router settings in a special web interface that each device is equipped with.

Important! To open the setup interface, you need to connect your computer to the device. Internet access is not required.

To open the site for setting up your router, do the following:

  • Open your browser;
  • Enter in address bar IP address;
  • In the window that opens, log in - enter your username and password.
  • The address, network name and login pin code are indicated on a sticker located on the back of the router.
  • Some devices do not have login data - they need to be installed after logging into the interface.

Please note that some manufacturers set the parameters themselves - then you don’t need to do anything when you turn it on for the first time.

#3. Setup instructions

Most routers have a special wizard option that will help you quickly set the necessary parameters. For example, here, the item is called “Quick setup”:

The most important thing you need to configure is:

  1. Internet connection;
  2. Wi-Fi network.

Let's deal with the first parameter first. Our main goal is, of course, the operation of the Internet on devices:

  • Open the General Settings tab. Most often they are located in the WAN or Internet section;
  • Specify the provider connection type, username and password - you can see the information in the contract;
  • If the provider requires MAC address binding, provide the required data (from the contract).

Important! If the provider uses (DHCP), then the connection to the network will occur in automatic mode. Skip this section of the instructions; there is no need to reconfigure the router.

  • Open the section called Wi-Fi. It may be called differently - Wireless network/Wireless/Wireless mode;
  • In the “Network name” or “SSID” field, enter a new name (in Latin only);
  • In the “Wireless network key” field, enter the created identification code;
  • Security type – WPA2 – Personal;
  • Change the region to the location in the appropriate line;
  • Save your changes.

If you want to change your router settings, we recommend that you change the factory access code. This is important if you want to protect yourself from unauthorized entry. Here's how to do it:

  • Find the security or privacy settings section;
  • Change the data to a new, reliable code.

All of the above instructions apply if you need to set up a new router instead of an old one or install completely new equipment. By the way, we suggest you watch a general video on how to set up a router. It is perfect for those who are not confident in their abilities, because it shows the whole process step by step and in detail!

Now you know everything about how to set up the Internet on a Wi-Fi router via a computer - use our article to achieve results. Just follow the instructions and in a few minutes you will be able to successfully surf the Internet.

Nowadays there are a huge number of different Wi-Fi routers on sale from different manufacturers. And that’s good, there’s plenty to choose from. But immediately after purchasing a router, we need to install, connect and configure it. And if the connection process is practically the same depending on the model, then the setup process itself and the page with the router settings can be different even from the same manufacturer.

It is very difficult to give detailed and step by step instructions on setup different models. But I'll try. In this article I will describe in detail and show how to install and configure a Wi-Fi router. Regardless of what manufacturer and model you have. This universal instruction is suitable for both setting up a new router and re-configuring it. You can do everything yourself. And you don’t have to pay specialists for setup.

Login to the router settings. How to log into the web interface?

Each router has its own web interface (site with settings, control panel), which can be accessed through a browser by going to the appropriate address.

Important! To go into the router settings and configure it, your device (PC, laptop, smartphone, tablet) must be connected to the router via cable, or Wi-Fi networks. At the same time, there may be no access to the Internet on the computer. You don't need internet to log into the control panel!

If you have a high-speed connection on your computer (maybe with your provider's name), then after connecting through the router there is no need to start it!

To enter the settings we need find out the address our router and factory username and password for authorization. This information is located on the body of the device itself. It looks something like this:

On a computer or mobile device that is connected to the router, open a browser (Opera, Chrome, Yandex.Browser, etc.) and go to the address indicated on the case. Or try 192.168.1.1 and 192.168.0.1.

Important! We enter the address in the address bar, and not in the search bar. Many people get confused and instead of a page with settings they end up on a page with the search results of some search engine.

On the login page you need to specify a username and password. The factory settings are indicated on the device body. Most often these are admin and admin. On some models, the default settings are not protected, and immediately after logging into the control panel, you need to set a login and password.

Articles that may be useful to you at this stage:

If the settings page has opened, we can continue. If not, then see the article with solutions to this problem at the link above.

How to set up a Wi-Fi router?

In order to use the Internet through a router, you need at least:

  • Set up an Internet connection.
  • Set up a Wi-Fi network.

In most cases this is enough. I also recommend changing the password that protects the router’s web interface. Is there some more IPTV settings, USB drives, parental controls etc., but not everyone needs them.

In the control panel of almost every router there is a so-called “Wizard” quick setup", also known as "Quick Setup". On some devices, it opens immediately after entering the control panel. With its help, you can set up a Wi-Fi router step by step. Internet connection, wireless network, etc. For example, what it looks like on TP-Link:

You can try it, it's very convenient.

Internet setup. The most important step

The main thing is correctly configure the router to connect to the provider. If he cannot connect to the Internet, then all devices will have a “No Internet access” connection. Many users who try to configure everything themselves most often encounter problems at this stage.

Each Internet provider uses a specific type of connection. Dynamic IP (DHCP), Static IP, PPPoE, L2TP, PPTP. This type of connection must be specified in the control panel of the router, and certain parameters provided by the Internet provider must be specified.

Important! You must know exactly what type of connection your provider has. Also all the necessary data for connection (Username: Password), if they are necessary. As a rule, this information is specified in the contract that you received when connecting to the Internet.

Some providers bind by MAC address. It would also be desirable to clarify this.

If your provider uses a “Dynamic IP” (DHCP) connection, then the Internet should work immediately after connecting, since this type of connection is set by default on routers.

If the Internet through the router is already working (and you haven't run any connections on the computer), then you can skip this section and go straight to setting up Wi-Fi.

When the connection type is PPPoE, L2TP, PPTP, or Static IP (which is very rare), then you need to set required parameters. Usually, this is the login and password that your provider gave you. In the control panel, the section with these settings is most often called: “WAN”, “Internet”, “Internet”.

For example, what the PPPoE connection setup looks like on an ASUS router:

Other examples:

Target: so that the Internet through the router works on all devices. Via cable and Wi-Fi. If this does not happen, then there is no point in continuing the setup.

You can always call the provider and clarify what parameters should be specified and where. They help many people over the phone.

Articles that may be useful to you:

I hope everything worked out for you.

Changing Wi-Fi network settings

I highly recommend changing your Wi-Fi network name and password. It is also advisable to set your region. Everything is simple there. This can be done in the section with wireless network settings. It can be called differently: “Wi-Fi”, “Wireless network”, “Wireless”, “Wireless mode”. If you have a dual-band router, then the settings must be set separately for the network at 2.4 GHz and 5 GHz.

  • In the "Network name" (SSID) field you need to enter a new name. In English letters.
  • In the "Password" field (wireless network key) create and write down a password. Minimum 8 characters. Security type - WPA2 - Personal.
  • Well, there should be a “Region” field there. Change it to yours.
    • IPTV on ASUS routers.

    If something doesn’t work out for you during the setup process, you can always reset the settings to factory defaults and try setting everything up again. Find the “Reset” or “Reset” button on the case, press it and hold for about 10 seconds. The indicators will tell you when the reset occurred.

    You can leave questions in the comments. I just have a small request, describe the problem in detail. Write the router model. Otherwise, it’s very difficult to understand and advise something when you don’t understand the question itself. Best wishes!

If you decide to install wi-fi at home, at work, or in any other place, then you definitely need to purchase a special device called a router. This is a special device that distributes wireless Internet at a certain distance. Routers are classified by power, number of connected objects, speed, range, etc. Therefore, if you want to purchase a router, be sure to check out its specifications. Once you purchase this device, you will need to install it. I am sure that 99% of users will have problems with this, so this article is dedicated to how to install a router.

How to install a router - step by step guide

There are a huge number of routers from different manufacturers, but the most popular D-Link. That is why we will figure out how to install a D-Link wi-fi router.

1) Open the box with the purchased device, take it out and connect it to the power supply. The lights on the front should light up. If they do not light up, then there is some problem with the router. On the back side we see several ports. We need a port labeled “Internet”, into which we must insert the plug that was connected to the computer.

2) In any of the other ports we place the cable that was included with the router. This cable needs to be connected to the computer (to the place where we pulled out the Internet cable).

3) Open any program that provides Internet access. We write the following numbers: 192.168.0.1. This page - home page settings. You don't need an Internet connection to connect to it.

4) We continue to figure out how to install the router. We have opened an authorization page with the fields name and password. In the name field we write admin, and leave the password field empty.

5) On the page that opens, select the Setup item, then the item on the left Internet Setup and then click Manual Internet Connection Setup ( Manual installation Internet connections).

6) In the Internet Connection Type section that opens, select the item called PPPoE user name/password and select the Dynamic PPPoE item. In the Name, Password and Password Confirmation fields, enter the data that is specified in the agreement with your Internet provider.

7) Look a little lower and see the “clone mac address” item. Click on it. In the Connect mode select item, put a dot opposite Always. The remaining items do not need to be changed.

8) Discussion on how to install is almost complete. All you have to do is figure it out. In the device menu, which is on the left, select Wireless installation, then the Manual button will appear in the center wireless setup connections, click on it and look at the main settings menu that opens. In the Wireless section, check the box next to Enable wireless network, and in the Wireless network name field, write any name. We also fill in the Wireless Network Key field and remember it. This field will store the password for your wi-fi. It is needed to prevent neighbors and other strangers from connecting to the router.

I hope that after reading this article, you have figured out how to install a router.

Good day.

So that you can organize a wireless Wi-Fi network at home and give everyone access to the Internet mobile devices(laptops, tablets, phones, etc.) - you need a router (even many novice users are already aware of this). True, not everyone dares to connect it and configure it themselves...

In fact, most people can do this (I don’t take into account exceptional cases when an Internet provider creates such a “wild” with its own parameters for accessing the Internet...). In this article I will try to answer all the most FAQ that I heard (and hear) when connecting and setting up Wi-Fi router. So let's get started...

1) What router do I need, how to choose it?

Perhaps this is the first question that users who want to organize a wireless Wi-Fi network at home ask themselves. I would start this question with a simple and important point: what services does your Internet provider provide (IP telephony or Internet television), what Internet speed do you expect (5-10-50 Mbit/s?), and at what protocol you are connected to the Internet (for example, now popular: PPTP, PPPoE, L2PT).

Those. The functions of the router will begin to appear by themselves... In general, this topic is quite extensive, therefore, I recommend that you read one of my articles:

searching and choosing a router for your home -

2) How to connect the router to the computer?

As a rule, the router itself includes a power supply and network cable to connect to a PC (see Fig. 1).

By the way, please note that back wall The router has several sockets for connecting a network cable: one WAN port and 4 LAN ( the number of ports depends on the router model. In the most common home routers, the configuration is as in Fig. 2).

Rice. 2. Typical rear view of the router (TP Link).

The Internet cable from your provider (which was most likely previously connected to the PC’s network card) must be connected to the blue port of the router (WAN).

Using the cable that comes with the router, you need to connect the computer’s network card (where the provider’s Internet cable was previously connected) to one of the router’s LAN ports (see Fig. 2 - yellow ports). By the way, you can connect several more computers this way.

At an important moment! If you don’t have a computer, you can connect the LAN port of the router to a laptop (netbook) with a network cable. The fact is that initial setup It is better (and in some cases, it is impossible to do otherwise) via a wired connection. After you specify all the basic parameters (set up a wireless Wi-Fi connection), you can disconnect the network cable from the laptop and continue working via Wi-Fi.

As a rule, there are no issues with connecting cables and power supplies. Let's assume that your device is connected, and the LEDs on it started blinking :).

3) How to enter the router settings?

This is probably the key question of the article. In most cases, this is done quite simply, but sometimes... Let's consider the whole process in order.

By default, each router model has its own address for entering the settings (as well as login and password). In most cases it is the same: http://192.168.1.1/, however, there are exceptions. Here are a few models:

  • Asus - http://192.168.1.1 (Login: admin, Password: admin (or empty field));
  • ZyXEL Keenetic - http://192.168.1.1 (Login: admin, Password: 1234);
  • D-LINK - http://192.168.0.1 (Login: admin, Password: admin);
  • TRENDnet - http://192.168.10.1 (Login: admin, Password: admin).

At an important moment! It is impossible to say with 100% accuracy what address, password and login your device will have (even despite the brands I listed above). But this information must be indicated in the documentation for your router (most likely, on the first or last page of the user manual).

Rice. 3. Enter your login and password to access the router settings.

For those who were unable to enter the router settings, there is a good article with reasons (why this could happen). I recommend using the tips, link to the article below.

How to log in to 192.168.1.1? Why it doesn’t log in, the main reasons are:

How to enter the Wi-Fi router settings (step by step) -

4) How to set up an Internet connection in a Wi-Fi router

Before describing these or those settings, a small footnote should be made here:

  1. First - even routers from one model range may have different firmware ( different versions). The settings menu depends on the firmware, i.e. what you will see when you go to the settings address (192.168.1.1). The settings language also depends on the firmware. In my example below, I will show the settings popular model router - TP-Link TL-WR740N (settings on English language, but understanding them is not so difficult. Of course, it’s even easier to set up in Russian).
  2. The router settings will depend on the network organization of your Internet provider. To configure the router, you need connection information (login, password, IP addresses, connection type, etc.), usually everything you need is contained in the Internet connection agreement.
  3. For the above reasons - it is impossible to give universal instructions, which is suitable for all occasions...

U different internet providers different type connections, for example, Megaline, ID-Net, TTK, MTS, etc. use a PPPoE connection (I would call it the most popular). In addition, it provides higher speed.

When connecting PPPoE to access the Internet, you need to know the password and login. Sometimes (as for example, MTS) uses PPPoE+Static Local: access to the Internet will be provided, after entering the password and login for access, the local network is configured separately - you will need: IP address, mask, gateway.

Necessary settings (for example PPPoE, see Fig. 4):

  1. You need to open the “Network / WAN” section;
  2. WAN Connection Type - indicate the type of connection in in this case PPPoE;
  3. PPPoE Connection: Username - specify the login for accessing the Internet (specified in your agreement with the Internet provider);
  4. PPPoE Connection: Password - password (similar);
  5. Secondary Connection - here we either do not indicate anything (Disabled), or, for example, as in MTS - we indicate Static IP (depending on the organization of your network). Typically, this settings item affects access to local network your Internet provider. If you don’t need it, you don’t have to worry too much;
  6. Connect on Demand - establish an Internet connection as needed, for example, if the user accesses an Internet browser and requests a page on the Internet. By the way, please note that there is a column below Max idle Time - this is the time after which the router (if it is idle) will disconnect from the Internet.
  7. Connect Automatically - connect to the Internet automatically. In my opinion, the optimal parameter is what you need to choose...
  8. Connect Manually - connect to the Internet manually (inconvenient...). Although for some users, for example, if traffic is limited, it is quite possible that this type will be the most optimal, allowing them to control the traffic limit and not go into the red.

Rice. 4. Setting up PPPoE connections (MTS, TTK, etc.)

It is also worth paying attention to the Advanced tab - in it you can set DNS (they are sometimes necessary).

Rice. 5. Advanced tab in the TP Link router

Another important point - many ISPs bind your MAC address network card and do not allow you to access the Internet if the MAC address has changed ( approx. each network card your unique MAC address).

Modern routers can easily emulate the desired MAC address. To do this you need to open the tab Network/MAC Clone and press the button Clone MAC Address.

Alternatively, you can tell your new MAC address to your Internet provider and they will unblock it.

Note. The MAC address is something like this: 94-0C-6D-4B-99-2F (see Fig. 6).

Rice. 6. MAC address

By the way, for example in “ Billine» connection type is not PPPoE, A L2TP. The setup itself is done in a similar way, but with some caveats:

  1. Wan Connection Type - the connection type must be selected L2TP;
  2. Username, Password - enter the data provided to you by your Internet provider;
  3. Server IP-address - tp.internet.beeline.ru;
  4. save the settings (the router should reboot).

Rice. 7. Setting up L2TP for Billine...

Note: Actually, after entering the settings and rebooting the router (if you did everything correctly and entered exactly the data that is needed), the Internet should appear in your laptop (computer) that you connected via a network cable! If this is the case, all that remains is to set up a wireless Wi-Fi network. In the next step, we will do this...

5) How to set up a wireless Wi-Fi network in a router

Setting up a wireless Wi-Fi network, in most cases, comes down to specifying the network name and password to access it. As an example, I’ll show the same router (though I’ll take Russian firmware to show both Russian and English options).

First you need to open the Wireless section (wireless network), see fig. 8. Next, set the following settings:

  1. Network name - the name that you will see when searching for and connecting to a Wi-Fi network (specify any);
  2. Region - you can specify “Russia”. By the way, many routers don’t even have such a parameter;
  3. Channel Width, Channel- you can leave Auto and not change anything;
  4. Save your settings.

Rice. 8. Wi-Fi setup wireless network in the TP Link router.

Next, you need to open the “ Wireless Security". Many people underestimate this point, but if you do not protect the network with a password, then all your neighbors will be able to use it, thereby reducing your network speed.

  • Version: you don’t have to change it and leave it automatic;
  • Encryption: also automatic;
  • PSK password is the password to access your Wi-Fi network. I recommend that you indicate something that is difficult to find by regular search, or by random guessing (no 12345678!).

Rice. 9. Setting the encryption type (security).

After saving the settings and rebooting the router, your wireless wifi the network should start working. Now you can set up a connection on your laptop, phone and other devices.

6) How to connect a laptop to a wireless Wi-Fi network

As a rule, if the router is configured correctly, there should be no problems with setting up and accessing the network in Windows. And such a connection is made in a couple of minutes, no more...

First, click on Wi-Fi icon in the tray next to the clock. In the window with a list of found Wi-Fi networks, select yours and enter the password to connect (see Fig. 10).

Rice. 10. Wi-Fi selection network for connecting a laptop.

If you entered the network password correctly, the laptop will establish a connection and you can start using the Internet. Actually, this completes the setup. For those who did not succeed, below are some links to typical problems.

The laptop does not connect to Wi-Fi (does not find wireless networks, no available connections) -

Problems with Wi-Fi in Windows 10: network without Internet access -

Wireless networks are a very convenient tool for solving everyday problems related to accessing the Internet. Today it is quite difficult to find a person who does not have a router at home. Installing a Wi-Fi router yourself is not a difficult task, and now we will look in detail at how to do it.

Device selection

Before moving on to the question of how to install a router, you should select it. Nowadays you can find a great variety of different models of Wi-Fi routers in stores. However, not all of them will suit your requirements. There are several parameters to consider in this matter:

  1. presence of powerful external antenna– the description must indicate the power, for example, 5;
  2. convenient and intuitive interface - this will allow you to easily and quickly understand the settings. By far the simplest and most intuitive clear interface have routers from the company -;
  3. supported standards – there are several standards that are most common:
    • 802.11 is an old standard operating at 2.4 GHz;
    • 802.11 – is also considered obsolete and operates at a frequency of 2.4 GHz;
    • 802.11 – new standard, which operates at a frequency of 5 GHz and has a higher data transfer rate over wireless networks(up to 300 Mbits). It is worth noting that routers that support 802.11 type can work with all types of devices, even with outdated models, operating at a frequency of 2.4 GHz. In this matter, it is best to give preference to routers that support operation on all these standards (make sure that the box bears the designation “N” - 300 Mbits);
  4. the presence of the required ports for connecting an Internet cable, modems, computers, and so on. Here you should proceed from your preferences and requirements.

When choosing equipment, we advise you to avoid cheap Chinese devices. Such gadgets work with constant glitches. Now let's move on to the main question - how to install a router at home. It's probably best to start by determining where the access point will be located.

Determining the location

It is preferable to place the router in the central part of the room (or as close to the center as possible) somewhere under the ceiling or on a cabinet.

The higher the access point is, the fewer obstacles there are in the signal path and the larger the coverage area.

When deciding how to install a Wi-Fi router at home, you should avoid mirrors, as they reflect the signal and radio waves simply will not pass through; household appliances, especially those that emit strong electromagnetic waves, such as microwaves(microwave), refrigerators, radios, home phones and so on.

If the room is quite large and one router is not able to cover the entire territory, then you can significantly increase the coverage area. It is worth noting that each router has wall mounts. So, now you know where and how to install the router yourself. Now you can proceed to configuration.

Equipment setup

Usually when first turned on Wi-Fi router Already working. All you have to do is change the network name and assign a password for security.

First, we need to go to the access point parameters. To do this, you need to find out the IP address of the router. It is indicated on the factory sticker that is on each router (carefully inspect the gadget from all sides).

You can also find it out on the command line. Just connect to the network, open command line, enter the ipconfig command and click . Next, we need to find the line “Main gateway” - the address we need will be there.

Now you need to enter this IP address into the address bar of any browser and click. Typically, the IP address looks like this: 192.168.0.1 or 192.168.1.1. There may be other meanings - this has already been clarified by the methods described above.

So, Wi-Fi installation The home router requires two setup steps:

  • setting up local network and Wi-Fi;
  • setting up an Internet connection.

Let's take a closer look at both points.

Setting up a local network

In the question of how to install a new router, first of all you should look at setting up the local network and Wi-Fi connections. We will look at further steps using the example of setting up a TP-Link router. If you have a different model, then don’t worry: all routers are configured according to the standard scheme. Differences may only be in the names of some sections and in appearance interface.

So, follow these steps:

This completes the local network setup. But installing a router doesn't end there. Now we need to configure Internet access.

WAN setup

In order to set up an Internet connection (WAN), you need to know what type of connection your ISP uses. There are several options:

  • PPPoE – in this case you need to enter the login and password that your provider gave you;
  • binding by MAC address - in this case, as a rule, there is no need to manually enter network parameters;
  • static IP - this means that you are assigned a specific IP address and other parameters that must be entered manually.

In any case, you will have to call your provider and find out exactly how the router is configured (what type of connection is used).