Setting up routing d link dir 320. An old horse, it doesn’t spoil the furrow

Ports - 1 WAN and 4 LAN. The first type of WAN port is used to connect to a wide area network - in our case, this port is used to connect an incoming cable from the provider. Connect the cable that goes into the apartment to it. LAN - used to connect computers located in your apartment. Connect to them using regular network cables(patch cords) computers that need to access the Internet. The router dir 320 has a built-in administrative interface for configuration, simply put - a special web page, by going to which you can configure the router. To do this, you need to use any computer connected to the LAN port on the router.

The default parameters of a new router in DIR models are usually indicated on a special sticker at the bottom of the case - usually IP - 192.168.0.1, login - admin, password - empty field, but there may be other values. Check these parameters on the sticker or in the user manual. If your router is not new and has already been used by someone, find in the instructions a paragraph on the procedure for resetting parameters to factory settings; usually for this you use a special recessed “reset” button on the back of the case, which you need to press with something sharp and hold for several seconds .

Please note that after connecting to the network, the new router automatically assigns a set to all computers connected to the LAN ports network settings, so make sure that no IP addresses are specified in the network card settings, all values should be set to “obtain automatically”.

Setting up a computer to connect to the DIR-320 router

We connect the DIR-320 router to a power outlet.
We connect the computer’s network card to the router with a wire, connect to any free port LAN1-LAN4.
We connect the Internet cable to the INTERNET / Lan port.
Go to connection properties by local network.

Select “Internet Protocol (TCP/IP)” and click “Properties”.

In “Properties”, check the parameters “Obtain automatically” and “Obtain DNS server address automatically”

We look at the automatically received settings.

Setting up a DIR 320 router for the Triolan provider

After you have found out the parameters of your router (IP address, login and password), open the browser and enter 192.168.0.1 in the address bar. If everything is correct, you will be prompted for authorization - enter your username and password. We log in using the following parameters:

Login: admin
Password: do not enter anything (empty).

Click “Internet Connection Setup Wizard”.

In the next window, click “Next”.

Set your password, then click “Next”.

We determine your time zone (Ukraine - GMT+02:00). NTP Server Used: ntp1.dlink.com, click “Next”.

Select the connection type “Static IP Address Connection”.

DNS addresses We indicate the following (for all subscribers of the Triolan provider):

DNS 1: 109.86.2.2

DNS 2: 109.86.2.21

We see a notification that the setup is complete, click “Connect”.

Let's check if the Internet is working, if so, then you did everything right!

Setting up wifi on the dir 320 router

It is very important to understand that correct setting wireless network security is responsible for limiting access to your account The Internet protects your money. If your wireless access point is not configured correctly, third parties may connect to it and use the Internet at your expense.

Please note that the wireless module is configured correctly and that your own accounting information– the task of the subscriber; the provider is not responsible for the safety of the subscriber’s funds in this case. The minimum level of security settings for the wireless module is an encryption level of at least WPA/ . The use of WEP or OpenSystem is strongly discouraged.

To configure the dir 320 module on the router, press the “SYSTEM” menu button, then “WIRELESS SETUP”, then select “MANUAL WIRELESS CONNECTION SETUP”

Wireless Settings

WiFi protected setup (WCN2.0) – disable
Enable Wireless - enable
Wireless Network Name (SSID) – any wireless network name convenient for you, for example HOME
Enable Auto Channel Selection – enable
WMM Enable – disable
Enable Hidden Wireless – disable
Security Mode – WPA/WPA2
Cipher type - TKIP
PSK/EAP - PSK
Network key – any secret key of your network (min. 8 characters, English letters and numbers)

Click “SAVE SETTINGS” - the settings will be saved.

After making any changes, you must reboot the router for them to take effect. To do this, click the “REBOOT” button in the menu on the left.

Video instructions for setting up the D-link DIR-320 router for VPN (PPTP) connection

Setting up a VPN connection on the D-link DIR-320 router

Dynamic PPoE Settings

My internet connection is – (Username/password)
Dynamic PPPoE - selected
User Name – your login for Internet access
Password – your password for accessing the Internet
Service Name - home
RetypePassword – retype your password for Internet access

Click “SAVE SETTINGS” - the settings will be saved. After making any changes, you must reboot the router for them to take effect. To do this, click the “REBOOT” button in the menu on the left.

To check the correctness of the settings and reconnect PPPoE, press the “STATUS” button in top menu.

On this page you can use the “CONNECT”, “DISCONNECT” buttons to initiate a connection or disconnect a connection.

The current connection status is displayed in the column on the left and one of the router's LEDs.

You can download it here.

If you purchased a new router or moved to a new place of residence with old equipment, then most likely you will need to configure the d link dir 300 Rostelecom router. This process is not as complicated as it seems at first glance. In this article we will prove this and consider all the stages of this procedure, as well as setting up the d link dir 320 Rostelecom router.

Preparing the router

Setting up a router dir 300 Rostelecom - old firmware

New firmware and work with the dir 320 model

Enabling WiFi protection

Conclusion

cost of Interactive TV from Rostelecom.

You can read how to connect Interactive TV through a router here.

After successfully logging into the main interface, the router will most likely prompt you to change standard password on your own. We enter the invented combination of characters in two fields, confirm and go through authorization again, but with new data. If everything is done correctly, you will see the main menu in the form of blue “buttons” of a fairly large size.

To start setting up the network, perform the following operations:

click on the first (lower left) button of the second line “Configure manually”;

in the upper text menu select “Network”;

open an existing “WAN” connection;

Scroll down the page and click “Delete” in the lower right corner;

wait until the page refreshes, the “Add” button appears on the right, click on it;

on the settings page that opens, specify the type of Internet connection – PPPoE;
we do not touch the port;

choose any name (this is what your connection will be called in “ Network connections" on the computer);

Below we indicate the login from the agreement with Rostelecom, as well as the password;

save the changes made, then click “Save” again in the center of the page.

At this stage, we put aside the Rostelecom agreement and check the settings of the dir 300 router - go to any page on the Internet. It should open without problems. All that remains is to configure wireless network. For this:

open the item WiFi menu(located next to “Network”);

in the SSID field, enter any name for your network and move on;
to set a password, save the changes and select from the available WPA2-PSK options;

Enter the password you created and save again.

That's all, the connection and wireless network are ready to go.

How to disable the Gudok service.

About transferring subscribers mobile operator Rostelecom on Tele-2 can be read here.

From this article you learned how to set up a dir 320 router for Rostelecom, as well as its previous model, and these instructions should work in most cases. If you have such a typical problem as the web interface being unavailable via IP (that is, the browser does not open the authorization page after entering the combination 192.168.0.1), then again go to the Internet protocol properties (where we set automatic IP/DNS acquisition) and switch network for working with static data. In the fields that become active, indicate:

168.0.12;

leave unchanged (should fill in automatically);

168.0.1;

DNS data from the contract;

also stated in the contract.

After applying these changes, the login page should become available. If you still have questions, watch this video:

And that's all. Tell us about your experience connecting to the Internet. Any questions in the comments are welcome!

On many devices, setup is quite easy if you know all its nuances. To make the connection, you need to outline a plan for the sequence of operations to configure the main equipment to work on the global network together with the device and implement the setup of the D-Link Dir 320 router.

Work order

The instructions we will follow are as follows:

Setting up a network card in relation to different operating systems using the example of Windows XP and G7.
Troubleshooting problems when turning on and operating the modem.
Replacing an old microcircuit or flashing a new one for proper operation Wi-Fi router D-Link Dir.
Basic network settings for different operators.
Setting up a Wi-Fi network.

Inexperienced users, when connecting the device, think that it will automatically tune to the desired provider and they will be connected to the global network. In fact, it is easier for them to call an employee of a company that provides such services. And who does not want to spend personal savings, we advise you to read the instructions for initializing the router located below.

Setting up a network card

Before installing the router, it is necessary for the computer to recognize the network card, then you need to set the IP address to the “automatic” position. This is necessary to synchronize the settings of your PC with the D-Link device, which has this specified in the factory settings.

We proceed according to the following scheme:

Click on “Start” and enter it.
Click on “Control Panel”.
We find the picture with the inscription “Network connections” and enter.
In the window that appears, select the picture next to which there is the inscription “Local Area Network Connection”.
Then right-click on it and find the “Properties” item.
Having entered it, put a tick on the inscription “Protocol (TCP/IP)” and click on “Properties”.
At the end, put the dots on “Automatic” and click “OK”.

The scheme is as follows:

Click on “Start”.
In the search engine (the line right above the “Start” button) enter the word “Network”.
In the window that appears, look for the inscription about the local network and click 2 times.
Then, by clicking on “Properties”, look for “Protocol version 4” and double-click.
Select “Automatic” and click on “OK”.

How to set up a D-Link Dir 320 NRU router without problems

After setting up the card on your PC, you need to make sure the IP address is correct.

Return to the item labeled “Local Area” and in the window that opens after double-clicking, select:

"More details" on Win XP.
"Information on Win

The IP address will be something like 192. 168. 0. XXX

If the address is not received, then the number will be 169.ХХХ. XXX. XXX.

XXX – any number (for example, 101, 204, 3) not more than 255.

To insert the correct addresses you will need to return:

in Protocol (TCP/IP) for Win XP.
Protocol 4 (TCP/IP v4) for Win

The detailed setup should look like this

At the end, click “OK”.

Replacing an old microcircuit or flashing a new one

We will explain step by step how to flash the router firmware using a PC, in other words, how to reset the original parameters.

Pre-download current version your device from the pages indicated in the figure:

To reset and create necessary settings Some models require disconnecting the Internet cable from the PC. So, check both options.

How to login - Link 320:

Connect your router to your PC and log into your browser.
You must enter the following in the address line: 192. 160. 1 – then press Enter and log in.
Enter the word admin in the “Login” field, and then Next or OK.

If login fails, try another option:

Enter the word admin in the “Login” cell and in the “Password” column.
In older D-Link devices, the firmware version looks like this:

To flash:

go to “Maintenance”;
then on the left in the “firmware update” menu;
then click on “Browse”;
find new option firmware;
At the end, click “apply” and wait for the result.

New devices may have three different patterns:

First option.

We look for the word “System” in the left menu and click on the button. Next, in “Software Update”, turn on the “Browse” scanner and select the required file.

Second option

“Configure manually” – “System”, go to the “Software update” item and select the file.

Third option

“Advanced settings” – “System”, then click forward and click on “Software update”.

After all the switching, you need to click on the apply button (“Update”).
Next you will need to wait about 7 minutes. This is necessary to complete the operation completely.
As soon as the installation occurs again, you must enter 192. 168. 0. 1 into the browser address bar and log in.

Connecting to providers and Wi-Fi

Beeline Communication

First, go to “Advanced settings” - “Network” - “WAN” - “Add”.

In the connection columns “Type” and “Name” – click L2TP + Dean. IP. in the first and any inscription in the second.
In the “User” (Name) section and in the “Password” column, enter the information received from the technicians who connected the equipment.
In the “MZT Address” field, enter – tp.internet.beeline.ru, then “Save” in one window and “Save” in another.

Settings D-link router Dir 320 Beeline is finished.

Communication Rostelecom

The primary actions are the same as in connection with Beeline. Further:

In the “Type” column, click PPPoE.
In the “PPP” field – in the “User” (Name) item and in the “Password” column – enter information from Rostelecom employees.
Click “Save”.

Wi-Fi setup networks

It also starts with “Advanced settings”, but then click “Wi Fi” - “General” - “SSID”, enter any inscription - the name of your personal network and click on “Change”.

Next, go to “Security” – “Network Authentication:” – “WPA-PSK2”, enter 8 or more characters in the “Encryption Key” and click “Change”.

Congratulations. You did everything right.

Visual instructions for setting up Dir 320 (video)

Useful video with router settings:

You can configure the router yourself. By doing this, you will save money, learn how to set up a device, and, perhaps, start your own business connecting users to the Beeline and Rostelecom networks.

Preparing the router for work

Before you start working directly, you need to inspect the device itself and perform a few simple operations:

connect the power cord and make sure that the “Power” indicator is on;
connect the Internet cord to the appropriate connector: there are 5 in total;
Verify that the Port 1 and Operation LEDs on the front panel are lit. WiFi networks, indicating that the cable is connected correctly and the signal from the provider’s servers reaches the device.

Important: the first four connectors are designed to connect a computer and a router via cable. Fifth for connection telephone wire(Internet), as a result of which d link 300 will take on the function of an ADSL modem.

Now we take out the documents that Rostelecom provided us; they are needed to configure the dir 300 router.

How to configure a dir 300 router with the old web interface

Setting up the d link dir 300 Rostelecom router begins with preliminary computer settings. They are carried out as follows:

Press the code combination Win+R on the keyboard. The “Run” window will open;
enter the combination ncpa.cpl into the empty field;
in the network connections window that opens, select your current one (which you are setting up) and open its properties;
from the list, select Internet Protocol version 4 and also go to properties;
if any IP and DNS addresses are specified, switch the network to automatically receive data.

Next, open the browser and, just as when setting up the dir 320 router for Rostelecom, enter address bar combination: 192.168.0.1, which will take us to the authorization page. There is no need to know the login and password when setting up a new device (purchased and never used), since the value is the same for both fields - the word “admin” is strictly in lower case. If an error appears indicating that wrong password, this means that the router has already been configured before and you need to find out the newly installed Password or reset the value by pressing the Reset button.

After successfully logging into the main interface, the router will most likely prompt you to change the standard password to your own. We enter the invented combination of characters in two fields, confirm and go through authorization again, but with new data. If everything is done correctly, you will see the main menu in the form of blue “buttons” of a fairly large size.

To start setting up the network, perform the following operations:

click on the first (lower left) button of the second line “Configure manually”;
In the top text menu, select “Network”;
open an existing “WAN” connection;
Scroll down the page and click “Delete” in the lower right corner;
wait until the page refreshes, the “Add” button appears on the right, click on it;
on the settings page that opens, specify the type of Internet connection – PPPoE;
we do not touch the port;
choose any name (this will be the name of your connection in “Network Connections” on your computer);
Below we indicate the login from the agreement with Rostelecom, as well as the password;
save the changes made, then click “Save” again in the center of the page.

open the WiFi menu item (located next to “Network”);
in the SSID field, enter any name for your network and move on;
to set a password, save the changes and select from the available WPA2-PSK options;
Enter the password you created and save again.

That's all, the connection and wireless network are ready to go.

Setting up a router dir 320 Rostelecom

Since the settings for the new firmware of the Dir 300 router and the main firmware of the 320 model are practically the same, we present general instructions on network settings this type Rostelecom devices.

The initial setup of the d link dir 320 Rostelecom router is carried out in exactly the same way as described earlier:

connect network cables and set automatic IP/DNS acquisition;
after that, log in with standard data and set your own login password;
in the interface window that opens, look in the lower right corner - “Advanced settings”;
in the “Network” field, select the first submenu item – “WAN”;
we've already chosen existing connection and by analogy, click “Delete”;
add a new connection in the same way as in the previous paragraph, entering the network name and data from the contract, and then save it;
open the notification that appears (light bulb in the top menu) and click “Save”;
refresh the page and observe the connection status “Connected”.

This completes the setup of the router dir 320 Rostelecom via a wired connection. Check the functionality of the connection by going to any of the search engines or to the website social network. If everything is done correctly, the Internet will work.

Setting up a WiFi router d link dir 320 Rostelecom

To configure the d link dir 320 Rostelecom router for “distribution” wireless connection, you need to return to the main menu and open the advanced settings again. Next to the “Network” field you can find the wi-fi configuration functionality we need. Go to the “Basic Settings” submenu and specify, as in previous firmware, network name. Then we go back a step and open the security settings, where you need to set the same type of network authentication and the same long password (at least 8 characters) as on the d link dir 300 router. Save the changes twice (the second time in the notification above) and check WiFi network availability on any suitable device.

168.0.12;
leave unchanged (should fill in automatically);
168.0.1;
DNS data from the contract;
also stated in the contract.

After applying these changes, the login page should become available. If you still have questions, watch this video:

And that's all. Tell us about your experience connecting to the Internet. Any questions in the comments are welcome!

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.0.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Changing the factory password

Default: Login admin, password admin.

In the router interface, you need to go to the tab System, menu Administrator password.

In field Password (New Password) Enter a new password.

In field Confirm Password repeat new password.

After this, the router will prompt you to re-enter its settings.

Setting up an Internet connection

On the page Advanced settings; select Net; ⇒WAN;.

Click on the button Add.

Setting up a PPPoE connection

In field Connection type: select PPPoE
In field Port select the WAN port - it is listed there as Port 5.
Username: Your login from the contract
Password: Your password from the agreement
Password confirmation: repeat password
Authentication algorithm: Auto
Keep alive
MTU

In field Miscellaneous NAT And Firewall.

Enable IGMP.

Setting up an L2TP connection

In field Connection type: select L2TP + Dynamic IP
In the Port field, select the WAN port - it is listed there as Port 5.
Username: Your login from the contract
Password: Your password from the agreement
Password confirmation: repeat password
VPN server address: enter the address of the provider's VPN server
Authentication algorithm: Auto
Keep alive- check the box for permanent connection
MTU- change the value to 1450 or less

In field Miscellaneous check that the checkboxes are checked NAT And Firewall.

If your provider provides Internet television service, check the box Enable IGMP.

Configuring PPtP (VPN) while automatically obtaining a local IP address (DHCP)

In field Connection Type: select PPTP+ Dynamic IP
In field Name enter the name of the connection (you don’t have to change it)
Username: Your login from the contract
Password: Your password from the agreement
Password confirmation: repeat password
Connect automatically: put a tick
MTU change the value to 1450 or less
Authentication algorithm: Auto
Keep alive- check the box for permanent connection
Save the settings with the button and reboot the router.

Setting up Wi-Fi on the router

1. From the advanced settings page, go to the tab WiFi, select the item basic settings; and set the desired name wireless point access SSID. After that, click Change;.

2. After this, it is also recommended to set a password for your wireless network. To do this, go to the Wi-Fi security settings, select the authorization type (WPA2/PSK recommended), and then enter any password of at least 8 characters - this will help protect your wireless network from unauthorized access. Save your changes.

That's all: now you can try using the Internet via wireless Wi-Fi connection from a laptop, tablet or any other equipment.

Checking Internet connection status

If the connection is created correctly and there are no problems on the part of the provider, then in the column " Network information", Status WAN connections it will say connected and your IP address.

Saving/restoring router settings

Select saving the current configuration. To save the current settings of the router, the settings file will be saved to the specified location on the hard drive.
To restore settings from a file, you need to click and select Loading a previously saved configuration into the device, specify the path to the settings file, then click the button.