Connecting keenetic giga ii to another router. Description of the Zyxel Keenetic Giga II router, its connection, firmware and configuration

Notes
1. Experienced users can update the firmware version of the router to a more current one.

2. If you lose control of the router (the web configurator page (192.168.1.1) is not available) it will help you restore operating system router.

Let's move on to the setup.
The router is configured using a browser via the Web interface. Physically, to set up, you can connect to the router using either an ethernet cable or via Wi-fi.

1. If not via Wi-fi, connect the Ethernet cable included in your apartment to the port WAN Your router.

2. Reset settings network card or wi-fi adapter on the computer if other devices were previously connected to it. For this purpose in Windows XP Start, Control Panel, Network connections. IN Windows 7 left click on the button Start, select Control Panel, Further Network and Internet, then Network Control Center and shared access, Change adapter settings. In the window that opens right click mouse click on the icon Connections by local network or wireless connection and in context menu select item Properties.

Left click once Internet Protocol TCP/IP(for Windows 7 - Internet Protocol Version 4 (TCP/IPv4)) and click on the button Properties.

Adjust the settings as shown in the figure below:

3. If not wi-fi, connect an Ethernet cable between the computer’s network card and one of the router’s ports, for example port No. 1, as shown in the figure.

4. Launch your browser and address bar enter http://192.168.1.1 and press Enter. In the authorization window that appears, in the field User Name enter admin, field Password enter 1234 and press the button OK.

5. Settings network connection.

Internet.
Broadband connection (ISP).

3) In the field Configuring IP settings select Automatically.
4) In the field MAC address select Default
5) In the field MTU size enter 1400 .

Note. When setting the IP parameters to "Automatic", all IP addresses and routing will be sent to the router automatically.
After filling in all fields, click the button Apply.

6. Setting up an Internet connection.

At the top of the page, select the tab PPPoE/VPN. 1) In the field Type (protocol used) select L2TP.
2) In the field Connect via select Broadband connection (ISP).
3) In the field Server address enter l2tp.freedom.
4) In the field Username
5) In the field Password
6) In the field Authentication algorithm select CHAP. After filling in all fields, click the button Apply.

7. Wi-Fi setup.

Features of Wi-Fi setup in the updated Keenetic II series.

The updated Keenetic II series now has an easy-to-access button WiFi on the top cover of the case, combining the functions WPS(WPS (Wi-Fi Protected Setup) is a standard designed to simplify the process of setting up a wireless network.) and allows you to turn off and on the Wi-Fi module of the device with a long (3 sec.) press. Also in the router settings it became possible to change the actions of the buttons WiFi And Fn.

WiFi.
1) In the window that appears, in the field Network name (SSID) Enter your login to access the network from the subscriber's Registration Card.
2) In the field Use connection protection select WPA-PSK + WPA2-PSK.
3) In the field WPA key Enter your password to access the network from the subscriber's Registration Card.
4) In the field Radio channel number: select 11 or 12 (If the network is not congested, auto is fine).
5) After filling in all fields, click the button Apply.
Note 1. If you have apple devices (iPhone, ipad, macbook), then the channel is selected up to 10.
Note 2. If the router was configured via Wi-Fi, for further configuration you will have to connect to the router again by following the steps in step 12 of these instructions.

8. Setting up IGMP for watching IPTV.

Select a section at the bottom of the page home network . At the top of the page, select the tab IGMP Proxy. Check that the settings are correct according to the screenshot below:

9. Allocation of a port for an STB set-top box.

If you need to allocate a port for connecting an STB set-top box to watch IPTV (in this case, the port of the router to which the set-top box is connected will be removed from the control VLAN and the set-top box will be connected in the same way as connecting through a separate switch/switch), follow these steps:
1) At the bottom of the page, select a section Internet.

2) In the window that appears, click on Broadband connection (ISP).
3) In the new window, check the box Use connector under the port to which the STB set-top box is connected. In our example, this is port 4.
4) Click the button Apply.

10. Set up your Wi-Fi card on your computer to access the network.

To do this, left-click once on the network card icon in the lower right corner of the screen (next to the clock).

In the window that appears, click the button To plug and enter Access key in wireless network which you asked earlier.

In windows 7/8

Select our connection and click on it. Check the box “connect automatically” and click “connect”.

If our connection has an exclamation mark, it means it does not have a password. Anyone can connect to your network.

Enter the security key. Click “OK”.

If everything is in order, we will see the following picture.

In order to get to the router’s web interface, you need to open your Internet browser and type 192.168.1.1, User Name in the address bar admin (Username), Password – 1234 (provided that the router has factory settings and its IP has not changed).

Changing the factory password

For security reasons, it is recommended to change the factory password. Default: Login admin, password 1234. In the router interface you need to go to the “ tab System", Further password. In field "New Password" enter New Password. It must be repeated in the next field. Next, save the settings by pressing the button “ Apply».

Setting up Wi-Fi on the router

WiFi.

In the window that appears, in the field Network name (SSID) enter the name of your network (any)
In field Use connection protection select WPA-PSK + WPA2-PSK
In field Network key enter your password to access the network (any)
In field Channel: select Auto
Apply.

Setting up a network connection

NAT when automatically obtaining an IP address (DHCP)

Select a section at the bottom of the page Internet
In the window that appears, click on Broadband connection (ISP)
In field Configuring IP settings select Automatic
In field MTU size enter 1400
After filling out these fields, click the button Apply.

Setting up an Internet connection

At the top of the page, select the tab Authorization.

In field Type (protocol used) select PPTP
In field Connect via select Broadband connection (ISP)
In field Server address enter Server name or address(check with your provider)
In field Username enter your login from the contract
In field Password enter your password from the agreement
In field Authentication Method select Auto
Service Name, Hub Name, Description- may not be filled in
After filling in all fields, click the button Apply.

Setting up a PPPoE connection (Rostelecom, Dom.ru)

InternetAuthorization»

Internet Access Protocol: PPPoE
Username : Your login according to the contract
Password: Your password according to the agreement
Save the settings with the button "Apply."

Setting up an L2TP connection (Beeline)

In the router interface, you need to select the tab on the left “ Internet", in the list that opens, select " Authorization»

Internet Access Protocol: L2TP
Description: connection name
Server address: server name or address (specified in the contract)
Username : Your login according to the contract
Password: Your password according to the agreement
Authentication method: Auto
Save the settings with the button "Apply."

Its powerful hardware and ease of procedure Zyxel settings Keenetic Giga 2 attracts many users. Below is a description of this router, instructions for connecting it, updating software and setting it up.

Description

In this compact device the manufacturer managed to combine simplicity, good performance and wide functionality.

However, the cost differs only slightly from the previous model.

Therefore, it is not surprising that this WiFi router has become very popular among users. Gigabit ports are responsible for a fast and reliable connection to the network. Their standard number will suit most owners of small apartments for creating a home network of several computers.

The built-in amount of RAM is 256 Mb and allows it to function for a long time without failures or freezes, and the internal flash memory (16 Mb) is quite sufficient for software and its regular updates.

If it is necessary to cover a larger area with a wireless signal, it is possible to easily replace both antennas with elements with a higher gain. But even the power of the bundled translators is enough for a comfortable connection to Wi-Fi in a two- or three-room standard apartment.

How to connect?

Experienced users know that it is more advisable to initially connect the device to a PC via a wired connection. The procedure is no different from previous models and is completely standard, but for people performing these steps for the first time, a description of each step is given below.

You need to do the following:

The connector marked in blue and labeled “Internet” requires a cable from your communication service provider to be inserted;
Install one patch cord plug into the first yellow socket marked “Home Network” (it comes with the Zyxel Keenetic Giga II). Connect the second plug of this cable to the PC network card socket;
Using the supplied power supply, connect the device to the mains and press the “Power” button.

Reset settings to default

If your Kinetic has already been used before, then most likely you will need to reset its settings first. For a new device, you can skip this paragraph of the instructions and immediately proceed to the next one.

The algorithm of actions consists of just the following few steps:

Procedure for logging into the web interface

Manufacturers of “Giga” with the index “Two” have provided the possibility of simple setup, which will seem uncomplicated even to a novice user.

To open the parameter entry menu, you will need to do the following:

Launch any Internet browser familiar to the computer owner and try to open one of the pages on the global network, for example, from the “Favorites” folder. In this case, the Quick Settings menu is usually immediately displayed.

If the user is a beginner, then he can simply click “ Quick setup” and the wizard will quickly guide him through all stages of entering the main parameters that are copied from the contract with the provider.

Installing new firmware

Manual setting

To enter network parameters, you must perform the following steps:

Open the “Internet” tab (entering parameters differs for different types connections);
If you use DHCP with the assignment of "IP" in automatic mode, then you need to enter the following:

Entering WiFi parameters

The following steps must be followed:

Router Zyxel Keenetic Giga II - successful model famous brand manufacturer network equipment. This powerful device with a good set of parameters and functions that will provide a fast and high-quality Internet connection.

Users are already accustomed to the wide functionality of routers

Let's find out what is remarkable about this router model, how to configure it yourself, and, if necessary, change the firmware on the device.

The Zyxel Keenetic Giga II model is average in terms of parameters between Keenetic II and Keenetic Ultra. The first model costs a little less, but has weaker characteristics, so the choice should be made in favor of the Giga II. The other model is stronger, but also more expensive, and is more likely designed for demanding users.

The filling of the Zyxel Keenetic Giga 2 is 256 MB random access memory, 16 MB of memory for installing firmware, the router has gigabit ports and operates at speeds of up to 300 Mbit/s. Such indicators are optimal for most users - they usually use the Internet at speeds of up to 100 Mbit, so the router will cope with it perfectly.

The model is equipped with 4 LAN ports and one WAN port, USB connectors for connecting various equipment, the power button - convenient so that you don’t have to turn off the router from the network, reset settings.

The router is equipped with two external antennas, which has a positive effect on the quality and coverage area of the signal. It is worth noting the stylish appearance - it attracts attention and looks quite interesting.

It also has a separate WPS button on top for quickly turning Wi-Fi on or off - it’s up to you to decide whether it’s useful or not, but if so, it’s a pretty practical solution. In general, the Zyxel Keenetic Giga II is best suited for a home or small office - it is quite powerful and not too expensive.

Setting up the router

To enter the settings menu you need to enter the combination 192.168.1.1. In the address bar of the browser, then an authorization window will appear - by default, the values admin are entered in both lines or 1234 in the password line.

Then you can proceed to setting up the connection, Wi-Fi work, IPTV and other functions.

To configure the network, select the Internet section at the bottom of the window, after which the parameters will differ depending on the type of connection.

To set up a connection via DHCP with an automatic IP address, follow these instructions:

Select the Broadband connection (ISP) line in the table;

You will see a form for filling out data, where, first of all, you need to mark the connector where the Internet cable is connected;
Next, check the lines “Enable interface” and “Use to access the Internet”;
When setting IP parameters, you should select the option from the list automatic receipt addresses;
Enter the number 1400 in the MTU line, save changes.

If the connection is made through a static IP address, then in this form you need to select the appropriate parameter for this setting and enter the address value, subnet mask and gateway in the fields below.

For connections that require you to enter more information, select the Internet section and open the Authorization tab, where in the window that appears you should do the following:

For a PPTP connection, check the box next to Enable and select this protocol from the list. In the “Connect via” line, select Broadband connection (ISP), below enter all the data from the provider - server address, login and password, check the automatic authentication algorithm;

To connect PPPOE, select the appropriate protocol in the “Type” line, enter the username and password specified in the agreement from the provider. In “Connect via” and in the verification algorithm, select the same options as before;

Connecting via the L2TP protocol occurs in almost the same way. All you need to enter is a description (connection name), user name and password, server address, and select an automatic authentication algorithm.

Setting up a Wi-Fi connection

The router is primarily used to access the network via wireless connection, which is configured like this:

Select the Wi-Fi section in the options menu on the bottom line;
Turn on the access point by checking the corresponding line, enter the network name;
The line for hiding the SSID, that is, the network name, was created in order to further secure it from being hacked. When activated, the connection will be invisible when searching for points on other devices. To connect to the Internet, you will need to manually enter your name and password, that is, if they don’t know them, they will not try to use your Internet;
In the WPA key line, come up with a key to connect to your network - try to create a more or less complex combination, again so that third parties do not use your Internet;
Select the channel automatically - in this case, the router itself will determine which of the available channels is least loaded and will connect to it.

It is also worth changing the factory login and password to access the settings menu itself after the first authorization - this is done in the System section.

If in addition to the Internet you use IPTV through a router, then installing it on this router is quite simple. Select the Home Network section from below and the IGMP Proxy tab. Choose to activate this feature and save your changes.

Software Update

To update or replace the firmware on Zixel Kinetic Giga you need to download current version firmware - please note that it is intended specifically for this router, after which we use the following instructions:

Go to the settings menu through the browser, select the System section;
Among the tabs, open the Files submenu, where there is a line to indicate the path to the firmware file;
After specifying the location of the firmware, click on “Replace” and confirm your intentions, then the installation of the new software will begin.

As you can see, the Zyxel Keenetic Giga II is remarkable appearance, powerful filling, but also easy to configure - create an internet connection Any user can use the router. It is no less easy to change the firmware on the device, so it is not in vain that the model attracts attention among other competitors. It well combines simplicity, functionality and affordable price.